Latest threads in ⚙ Mechanical Engineeringshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Re: CAD engineering software recommendations...
Solidworks has a free personal training version. It is basically equivalent to their commercial offering, but with limitations on filesharing, etc. 95% of the functionality of Pro/E with 25% of the...
2
|
19 years ago
|
2 | |
|
|
Re: Will this work?
Will it increase friction if bolts are tighten too much? Does it make sense to use a spring under a through bolt? Thanks
1
|
19 years ago
|
1 | |
|
|
Re: Any books on boat building out there?
"R2D2" : Get thee to and ask there. There must be a thousand books newer than that on the market. Earl Colby Pottinger
—
|
19 years ago
|
— | |
|
|
Re: Motor vehicle aerodynamics - in particular - Spoilers.....
"s" wrote in message news:bdv582$dgt$1$ No. Garry got the better deal. Even if Barry had found an intact discarded RS body out back of the shop and installed it on his 1.6, there would be no...
3
|
19 years ago
|
3 | |
|
|
source for # 12 x 4 inch stainless screws?
flathead, or similar top - needed to replace 16 penny stainless nails in 1985 redwood deck thanx - ^sig^ -please remove the spam block "nono" to reply
5
|
19 years ago
|
5 | |
|
|
Re: linear slide design question
if E is the length along the slide, and W is the width of the slide then the condition to guarantee free sliding is myu < E/W. If myu > 2*E/W then it will lock up no matter where it is loaded. in...
—
|
19 years ago
|
— | |
|
|
Re: Shear Stress of a Noncircular Section
The problem is that the nice closed form solutions rely on the assumption that plane sections remain planar, which is only true for circular sections
—
|
19 years ago
|
— | |
|
|
Re: Applying Le Chatelier To Global Warming
(Edward D. Vojcak) Message-id: Daydreaming may closer. Bret Cahill
—
|
19 years ago
|
— | |
|
|
Re: Any Books On Operating Off Spec., Jerry Rigs, Etc.?
My understanding is that the approved JAL procedure for fixing aircraft hydro lines with longitudinal cracks is to tightly wrap the tube with music wire for a few diameters on either side of the end...
—
|
19 years ago
|
— | |
|
|
Relief valve testing...
Question - Will a relief valve used for a hydraulic system operate at the same setting if subjected to test using gas? I need to validate the operation of an RV used with oil but only have a test rig...
3
|
19 years ago
|
3 | |
|
|
FFT analyser wanted
Currently our comapny wanted one FFT analyser, so far only SKF approach our ocmapny and we found that the price is too high for a basic set with software Prism4. Please recommend me more blands and...
2
|
19 years ago
|
2 | |
|
|
Re: Looking for 6-32 Threaded Screws in the UK
FWIW, 6-32 refers to a number 6 size, nominal dia = 0.1380" 32 threads per inch which is UNC. 6-40 would be UNF.
2
|
19 years ago
|
2 | |
|
|
Re: custom gear for timing belt: how to design?
Have you considered using timing belts with teeth on both sides? If I'm picturing things right, some of your idlers become drivers. Dodge calls them Dual Dyna-Sync, but there are plenty of other mfrs....
4
|
19 years ago
|
4 |