⧑ Industrial Control Group

Simulink Model

I have made a simulink model of Hydraulic Servo System, but it has a strange response. I want some one to check and guid...

0 comments posted 19yrs

posted by zeb_jehan

0 comments posted 19yrs posted by zeb_jehan

Model reference adaptive control question

Hi, dear friends, here is a question in model reference adaptive control plant: y(t) = a*y(t-1)+u(t-1) model: y_m(t) =...

1 comments posted 19yrs

posted by Yan.M.Zhao

1 comments posted 19yrs posted by Yan.M.Zhao

how to prove definite positive

Hi, my dear friends Plz help me with the following question x(t) = x(t-1)+P(t-1)theta(t-1)u(t) P(t-2)theta(t-1)theta(t-...

0 comments posted 19yrs

posted by Yan.M.Zhao

0 comments posted 19yrs posted by Yan.M.Zhao

Digital Speedometer, Calibration, Report Writing

Hi everyone I am working on a Digital Speedometer, i almost finished making PCB for the digital speedometer which inclu...

3 comments posted 19yrs

posted by rizkhan7

3 comments posted 19yrs posted by rizkhan7

Looking for recommendations for simple MEMS rate gyros and supporting curcuitry

Hi All. I'm going to be needing a simple (and inexpensive) rate gyro measurement system for an upcoming set of experime...

4 comments posted 19yrs

posted by mjardin

4 comments posted 19yrs posted by mjardin

Modeling the Dynamic Behavior of the Jacketed Stirred Reactor

The control objective for the jacketed reactor study is disturbance rejection. Specifically, we seek a controller desig...

0 comments posted 19yrs

posted by newspost

0 comments posted 19yrs posted by newspost

Calcualting Motor Torque

I am looking for a motor that meets the following requirements: Spin about a 50 gallon tank filled with liquid Tank of...

6 comments posted 19yrs

posted by abbeyg

6 comments posted 19yrs posted by abbeyg

Getting started with Control Engineering

Hello, I have some rather old books on Control Engineering that have material similar to the Wikibook on "Control Syste...

6 comments posted 19yrs

posted by jchondro

6 comments posted 19yrs posted by jchondro

Modbus Plus

Hi, I am interested in desigining a communication card with Modbus-plus connectivity. This card will have Anybus-s inte...

5 comments posted 19yrs

posted by amitpk

5 comments posted 19yrs posted by amitpk

Design Level of Operation for the Jacketed Stirred Reactor Process

The jacketed stirred reactor process has a reactant feed stream entering the top of the vessel. A chemical reaction con...

0 comments posted 19yrs

posted by newspost

0 comments posted 19yrs posted by newspost

Transformers...

In a production machine. Using 460 3p Y into a 120/208 3p Y transformer. Should the neutral be tied to the earth ground...

1 comments posted 19yrs

posted by st

1 comments posted 19yrs posted by st

Cheap or DIY String Pots?

Hello, I am aiming to overcome my natural ineptitude and build an oversize midi controller. Apologies for cross posting...

8 comments posted 19yrs

posted by gavspav

8 comments posted 19yrs posted by gavspav

Mechanica 2007 !!!

Hi This is Pranava from IIT Madras Mechanica is the technical festival of mechanical engineering, presented by Mechanic...

0 comments posted 19yrs

posted by pranava34

0 comments posted 19yrs posted by pranava34

Looking for a low cost MPC

I am responsible for the I&C on a small continuous chemical plant. We think that MPC can contribute to increased profit...

1 comments posted 19yrs

posted by JohnJohnJay

1 comments posted 19yrs posted by JohnJohnJay

lag compensation design assumptions?

I have a plant, Gp = 100/s(1+s/100)^2 I need to compensate this plant using lag compensation to give a phase margin of...

8 comments posted 19yrs

posted by bo

8 comments posted 19yrs posted by bo