ARM: Review - DML 1/35 Scale SU-100 - Premium Edition

Kit Review: Dragon Models Limited 1/35 Scale Kit Number 6356; Soviet
SU-100 Tank Destroyer - Premium Edition; 779 parts (378 parts in grey
styrene, 204 etched brass, 192 "Magic Link" track links, 3 clear
styrene, 1length twisted steel wire, 1 turned aluminum gun barrel);
price estimated at US $45
Advantages: new moldings mixed with upgraded parts from earlier
T-34-85 "Premium" kits; plentiful etched brass parts
Disadvantages: will not build into Czech-built version; still have to
cut out engine deck grille to replace it with screen version;
plentiful etched brass parts
Rating: Highly Recommended
Recommendation: to all Soviet armor fans
The story behind the SU-100 is fairly simple. F. F. Petrov took a
naval gun (basically a 3.9" gun from a destroyer) and converted it to
fit in a much smaller area; the gun could fire the same ammunition as
the naval weapon as well as the BS-3 "Beast Killer" heavy antitank
gun. But the new gun, designated the D-10, was originally an orphan.
Too big to fit in the T-34 (even as the T-34-100 it was a bad
combination) and unwanted for the IS-2 as the big 122mm D-25 gun was
more than capable of doing a better job, it went wanting until
somebody got the bright idea to replace the D-5S gun in the SU-85M
with the D-10. This was a quick fix, the SP units got a real Panther/
Tiger killer, and the gun found a new home. (This was before the
creation of the D-10T tank version and its marriage with the prototype
T-54 Model 1945; the rest, as they say, is history...)
Even today the Soviets apparently did not keep good records of the
number of SU-100s produced, even though they built them well after the
war and the Czechs produced them along with the T-34-85 tanks. One
estimate is around 4,800 but it does not break them down by producer.
While most of the postwar guns were used for providing weapons to the
Soviet satellites, the Czech built ones were exported, most famously
to Egypt where they served in both the 1956 and 1967 wars with Israel.
The most common spotting feature was a large stowage bin on the right
"cheek" of the casemate.
DML has now released a "Premium" level version of the SU-100, but
right up front I have to point out it will only build up out of the
box as the Soviet version. Even so, much of the kit appears to be new,
and it uses many of the conventions adopted with the T-34-85 kits.
The model has some neat touches, such as totally separate parts for
much of the casemate, cupola and gun mounting. There are also separate
sides to the casemate, but once again DML's directions sort of muddy
this up and do not plainly indicate they have to be attached to the
casemate in Step 5 (they are parts P4 and P5, and the upper hull is
C7.) While many modelers will probably figure this out (the parts are
not "blued out" and it is obvious where they go) it is still something
more than one will miss until after other bits are installed. A choice
of two rear plates for the casemate are provided, with and without the
"dutch door" flap behind the ammo loading/access hatch. Note that
while DML did put two faint ejection pin marks on the inside of the
flap, the ones on the outside are supposed to simulate the rotating
elements of the hatch dogs inside the hull (e.g. don't fill them in!)
The now all too common love/hate relationship with DML kits takes
over. They have made all of the grilles separate parts with optional
etched brass screens, but the one over the rear radiator air exhaust
is still molded solid. This means the modeler has to cut out the
somewhat thick screen section before the etched brass replacement can
be fitted. The etched blades for the louvers which are underneath it
are included, and unlike the last iteration of these they stand free
so there is no brass tab to interfere with mounting the screen
assembly when finished.
The wheels are new but for some odd reason DML pulled a Tamiya and
molded them with the segmented tire sidewalls. I am not sure why this
was done, as few vehicles that I have seen actually appear to have
these mold lines, and unlike the "weighted" tires in the M2 halftrack
kit (more a matter of taste than accuracy) this is a very uncommon
feature. The wheel centers are nicely done with separate hubs, but if
these wheels are used the modeler will have to clean them up, and the
mold ridge run all the way around the tires.
The "Magic Track" are pretty straightforward by now, but the usual
word of caution to leave the idler mounts (A6) loose until you have
the tracks ready to install so that you can get the right amount of
links to fit. Remember T-34 track links are "A" and "B" ones which do
not swap and must be added in pairs.
All hatches can be posed open or shut, which is nice, but since the
vehicle has not one whiff of interior I am not sure how many will be
used! (After-market time here...) It also comes with a choice between
"new" and "slightly used" fuel tanks, so the modeler has an option.
The exhausts designed for this kit replicated welded tubes with "slide
molded" openings.
The kit provides three gun barrels: original two-piece (halves) type,
a new "slide molded" styrene one, and a turned brass one. The
commander's cupola comes in 14 parts and has the option for either
styrene or brass components as well. In point of fact, this kit comes
with a plethora of brass parts - tie-downs, louvers, grilles, fenders,
trim, and even working snap-locks for the tow hooks. Most have a
plastic counterpart, but this is NOT a "Smart Kit" in that regard.
A nice sheet of Cartograf decals provides markings for five vehicles:
Unidentified vehicle, Bohemia 1945 (4BO green); 7th Mechanized Corps,
Hungary 1945 (worn whitewash over 4BO green); Unidentified unit,
Vienna 1945 (4BO green with red stars); 1st Guards Mechanized Corps,
Hungary 1945 (badly worn whitewash over 4BO green); and Unidentified
unit, Czechoslovakia 1945 (4BO green). Technical assistance on this
kit was provided by Nick Cortese.
Overall this is a nice kit, but hope someday DML provides the bits
and decals to do one of the Egyptian ones.
Thanks to Freddie Leung for the review sample.
Cookie Sewell
Reply to
AMPSOne
Loading thread data ...

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.