Spent the weekend printing free miniature people for my station platform and they came out better than expected

Nov 18, 2026 Last reply: 1 day ago 4 Replies
Jump to replies (4)

I grabbed that big free pack of low poly figures that's been floating around this forum and finally put it to use on my station platform. Printed about forty of them at 1:87 on my A1 with the 0.2 nozzle, and honestly I was expecting a stringy mess. They came out clean. Standing figures hold up great, the seated ones need a bit of care getting off the plate but nothing broke. I ran them in grey PLA and gave them a quick dry brush of dark brown on the shoes and hair, which takes about two minutes each and makes a huge difference at that size. The little shadows they cast across the platform in the evening light are the part I didn't plan for. My wife walked past and actually stopped to look, which never happens. One tip if anyone tries this: lay the figures flat on the plate rather than standing them up. They're low poly so they support fine either way, but flat gives you a much cleaner face and you just snap off the tiny tab on thier back.



If you've got a layout that's been looking empty, this sorts it out for basially nothing.


I printed a batch of similar figures for my freight yard last spring on my P1S and my experiance was the opposite on orientation. I stand mine upright with a small brim and they come out fine, but my figures are chunkier than the low poly style so they hold themselves up. The seated ones were the trouble for me too, they always wanted to lift at the front of the chair legs untill I slowed the first layer down a touch.

On painting, I went a diffrent route than dry brushing. I thin some cheap acrylic with water until it is almost a wash, dip a brush in and just flood it over the whole figure. It pools in the low spots and leaves the raised bits lighter, wich reads really well at that size. Grey PLA under a wash like that gave me decent skin tones without any actual effort.

The one thing I'd add from my own trial and error is to check the faces under a loupe before you commit to a full batch. Some of the free packs out there have merged or missing facial features that you can't see in the preview images, and I printed twenty of one guy with no eyes before I noticed. Cost me an evening of reprints. Now I do a test row of four different figures first and inspect them before running the rest overnight.

I printed a batch of these for my son's school diorama project on our A1 mini and took a different route with the paint. Instead of dry brushing, I did a wash with thinned dark grey acrylic, brushed it on sloppy and wiped the tops with a paper towel. The paint stays down in the creases so the faces and hands read as shaded at that size. My method takes about the same two minutes a figure but you don't need a steady hand, which mattered since my kid was doing half the work.

On size, I found 1:87 was pushing it with the stock 0.4 nozzle. Arms and cane-sized details fused or came out wispy. I scaled mine to about 1:64 and they printed clean first try in white PLA. If your printer only has the bigger nozzle, that might be the fix rather than fighting settings.

I also left mine standing up rather than flat, and the faces still came out fine, though mine were the chunkier poses from that pack, not the thin standing ones. The seated figures were the easy ones for me, no cleanup at all, which lines up with the freight yard poster's trouble coming from the chair legs lifting instead.

Either way, my son's little town square went from bare foam board to something people pick up and look at, so I get why the wife stopped walking.

Those low poly figures remind me of the old white metal miniatures we used to solder onto bases back in the day. Half the job was cleaning flash off with a hobby knife before you even got to paint. Funny how the new problems are things like tab removal instead of mold lines. One thing I do differently is bump the figure count way up per plate. At that scale the time cost is almost all plate loading and unloading, so I run a couple hundred at a time and sort them into shoeboxes by pose. Keeps a whole station crowd in reserve for when one gets knocked off the platform, which they will be.

One thing I'd flag on these free packs is the proportions. I checked a few of mine against a proper scale ruler figure and the low poly ones were running about a head too tall, so I scale mine to around 92 percent before slicing and they sit right next to the commercial figures without looking off. At 1:87 nobody notices a fraction of a millimetre, but the height difference between batches is the first thing the eye catches on a platform. Worth printing one figure and standing it beside whatever you allready have before you commit to a hundred of them.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required