⧑ Industrial Control Group

Probe for 50kV dc

Hiya, Is there any successful probe in the marketplace available that will give me a 4-20 mA (preferable but 0-10 V woul...

3 comments posted 22yrs

posted by PR

3 comments posted 22yrs posted by PR

FTSC under the limited input range & accuracy

In the following webpage the influence of restricted input range and accuracy upon the control output for the controlli...

0 comments posted 22yrs

posted by tiddler2

0 comments posted 22yrs posted by tiddler2

Microstepper Driver

The ProDrive-2000 Microstepper Driver: +24-80vdc / 1-7 amps / 200kHz. / Very low dissipation. Low cost ($79 USD) to the...

0 comments posted 22yrs

posted by johnny_smith_20022002

0 comments posted 22yrs posted by johnny_smith_20022002

Diesel engine + PM generator control

Hi All I am involved in a project where we have a diesel engine that has a permanent magnet DC generator attached direc...

1 comments posted 22yrs

posted by nospam

1 comments posted 22yrs posted by nospam

Input resolution ?

Can someone explain in layman's terms with a mix of technical terms the meaning of Input resolution regarding a buildin...

5 comments posted 22yrs

posted by EvilTool

5 comments posted 22yrs posted by EvilTool

Simultaneous stabalization - basic questions

Hello, I am wondering about the essential question of Simultaneous stabalization. I know it is different from robust st...

2 comments posted 22yrs

posted by jrwebber00

2 comments posted 22yrs posted by jrwebber00

Rotork Pakscan

Hi all! Has anyone had any good/bad experiences using the Modbus host link to a Rotork Pakscan system? Our latest proje...

6 comments posted 22yrs

posted by cdorrough

6 comments posted 22yrs posted by cdorrough

Method for solving optimal control

Hi All, I am doing a mobile robot project that requires to solve an optimal control problem. I can solve the two-point...

0 comments posted 22yrs

posted by everteq

0 comments posted 22yrs posted by everteq

Is this a position or velocity PI controller

Hi all, I have a discrete representation of an analogue PI control algorithm. On the surface it looks very much like a...

2 comments posted 22yrs

posted by ccdubs

2 comments posted 22yrs posted by ccdubs

Simulink model brower

Hi, I do not like to have the "model browser" in every Simulink window. Can someone tell me how to set it off defaultly?...

0 comments posted 22yrs

posted by scnnjst

0 comments posted 22yrs posted by scnnjst

Is PLC automation a good field to go into?

2003-08-12 19:25:06 PST from: Cameron Dorrough ( snipped-for-privacy@spamspamgoawayrmna.com.au) > The market leader wou...

3 comments posted 22yrs

posted by a_kouz

3 comments posted 22yrs posted by a_kouz

Where to put valve limit switches

I am doing an automation upgrade to a steam superheater at our gas plant. Upgrading from pneumatic control and hard wir...

5 comments posted 22yrs

posted by curtisk

5 comments posted 22yrs posted by curtisk

motor

how control a stepper motor through programming

3 comments posted 22yrs

posted by avijitece

3 comments posted 22yrs posted by avijitece

Inverse Laplace Transform of a multiple 2nd order pole

Hi all, I'm not able to find the inverse laplace transform of a multiple 2nd order pole: (LaTeX notation) \frac{ s + c }...

2 comments posted 22yrs

posted by daniele.pallastrelli

2 comments posted 22yrs posted by daniele.pallastrelli

controller non-minimum phase system

I think the solution to the inverted pendulum problem that I posted earlier boils down to the controller for non-minimu...

1 comments posted 22yrs

posted by sns3204

1 comments posted 22yrs posted by sns3204