⧑ Industrial Control Group

  1. Home
  2. ⧑ Industrial Control Group
2150 Threads Posts
to

New CAN and LIN hardware and Software

Announcing the availability some new products available from Computer Solutions PCAN Explorer ----------------------- T...
0 comments posted 21yrs
posted by sales
0 comments posted 21yrs posted by sales

Liquid Level Sensor for N2O

I have a requirement to measure liquid nitrous oxide level in a large tank, pressurized to about 700psi. Considered ult...
6 comments posted 21yrs
posted by robert
6 comments posted 21yrs posted by robert

System Identification with Slicot, problem

I have a MIMO thermal system where I am doing System Id. via. Scilab using the Slicot subprograms. I found that if I do...
2 comments posted 21yrs
posted by rerogers
2 comments posted 21yrs posted by rerogers

SCADA implementation project plan

Hi all, does anyone have a project plan template regarding a SCADA system implementation (design, develop, configure, te...
4 comments posted 21yrs
posted by sott99
4 comments posted 21yrs posted by sott99

AutomationDirect Ez-Touch Panel "Noise"

I have a new installation, consisting of an AutomationDirect DL450 and one of their "Ez-Touch" panels. Despite being gr...
8 comments posted 21yrs
posted by fake
8 comments posted 21yrs posted by fake

dsp motion controller needed for telescope

Hello, and thanks for reading this. We are about to upgrade our telescope control system and are looking for a DSP base...
12 comments posted 21yrs
posted by mckenna
12 comments posted 21yrs posted by mckenna

costate in Pontryagin Maximum Principle and LQG

Hi all, In order to stabilize a linear control system, is there a link between the costate while using the Pontryagin Ma...
0 comments posted 21yrs
posted by madyan110
0 comments posted 21yrs posted by madyan110

Stabilization

We need to stabilize a rotating device, on three axis, by feeding the controller with a signal that indicates, directly...
9 comments posted 21yrs
posted by lanarcam1
9 comments posted 21yrs posted by lanarcam1

GE Fanuc - Is It possible to 0...

Yes Is it possible to 0 for example T0001 to T00015 with one command on VersaMax Micro? T0001 to T0015 are diffrent var...
0 comments posted 21yrs
posted by bartekluk
0 comments posted 21yrs posted by bartekluk

Heater PID operation during cooling phase

Am programming a PID for a heater controller which works OK in the heating phase, but when the setpoint drops and it is...
8 comments posted 21yrs
posted by perfb
8 comments posted 21yrs posted by perfb

GE Fanuc - 0 bunch of variables

Hi Is it possible to 0 for example ten variable at the same time. They are on in continous block in memory ie. T0003-T00...
0 comments posted 21yrs
posted by bartekluk
0 comments posted 21yrs posted by bartekluk

GE Fanuc - connecting the GSM phone

Hi I have a GE Fanuc Versa Micro UDR0005 PLC. This model has two rs232 and rs485 ports. I want to connect my nokia 6210...
10 comments posted 21yrs
posted by bartekluk
10 comments posted 21yrs posted by bartekluk

Need help on Honeywell Uniformance PHD

Appreciate anyone familiar with Honeywell Uniformance Process Historian Database especially related to the RDI.
4 comments posted 21yrs
posted by datukbendahara69
4 comments posted 21yrs posted by datukbendahara69

control of header flow fanin/fanout

Hello, I'm working with schemes where there are a number of flows into, and out of, a fully liquid filled header (incom...
2 comments posted 21yrs
posted by bxvarley
2 comments posted 21yrs posted by bxvarley