Is a badly cracked forge lining still safe to run, or do I have to rebuild the whole thing?

Nov 20, 2026 Last reply: 1 hour ago 4 Replies

First reply

MossSage

Cracks in a gas forge lining are ussually just the refractory doing what refractory does, which is expand, contract, and crack every time you cycle it from forging heat back to room temp. Hairline cracks and shallow crazing are cosmetic. The chunk missing near the bottom is the…

Read the full reply

So I pulled the door off my gas forge the other night after a long session and finally looked at it under good light. The opening has cracks running every which way in the lining, and one chunk near the bottom has actually broken off. There's a pile of little broken bits on the ground under the door that I'm pretty sure used to be part of the interior. It still gets to forging heat fine and the burner sounds normal, but the inside looks rough. How do I tell the difference between normal wear and a lining that's actually done? The holes and thin spots worry me mainly because I don't want heat escaping somewhere it shouldn't and cooking the shell or the burner plumbing.



I did shut the propane off at the tank before poking around in there, since the inlet runs through the top right over the cracked area. Beyond that I have no idea what I'm looking at. Can you patch something like this with some kind of coating once it's cooled, or is this a rip it all out and start over situation? Money's tight so I'd rather patch it if that's not going to hurt me, but I also don't want to be the guy who kept running a forge he knew was falling apart.


Cracks in a gas forge lining are ussually just the refractory doing what refractory does, which is expand, contract, and crack every time you cycle it from forging heat back to room temp. Hairline cracks and shallow crazing are cosmetic. The chunk missing near the bottom is the part worth looking at, because that is where flux and scale eat away at castable linings. Here is my quick field test: with the forge completley cold, press your thumb firmly against the lining everywhere. If it feels rock hard, you are fine. If it dents, crumbles, or flakes off like dry biscuit, that area has been fluxed or overheated and is done. Also rap it with a knuckle, a solid lining rings, a cooked one sounds dull and sheds dust. What you do not want is bare shell showing thru, or a lining so thin the outside of the forge shell gets painful to the touch anywhere other than near the burner and door opening. Hot spots on the shell mean heat is getting through and that is what cooks your propane plumbing, so check the shell behind and around the cracked area with the forge running briefly from a distance, then shut down. If the shell stays dark, you are fine. If it glows or even looks cherry anywhere, that patch is done. As for patching, yes, and it is not a hack job if done right. For the missing chunk, buy a small tub of castable refractory cement, the same stuff you would have lined with, wet the area, and pack it in. For the cracks, thin coats of rigidizing wash or a refractory sealing coat brushed over the whole interior will hold loose fibers and crumbs in place and stop the pile of debris under the door. Let any patch dry fully per the can, then bring the forge up slowly the first few runs to drive out moisture without spalling the patch. If after that you still have bare shell or a soft spot bigger than a coin, then yes, cut it out and re-line that section rather than patch over it. But based on what you describe, sounds like normal wear plus one flux chewed corner, which is a patch and a reseal, not a rebuild. Do keep the gas shut at the tank while you are working near that inlet, no reason to have it live while you are poking around above cracked lining.

Mine did the exact same thing after about two years and I panicked over nothing. Patched the chewed up corner with a small tub of castable from the local pottery supply place, and that forge is still running fine three seasons later. One thing that helped me: I set a fire brick loose on the forge floor as a sacrificial layer. Flux and scale chew on that instead of the lining, and I just swap it when it gets gnarly. Costs almost nothing and saved me from doing this repair twice.

Also, when you button it back up, run some soapy water over the fittings on that inlet while the gas is on. Bubbles mean a leak. Twenty seconds of checking beats wondering about it later.

Agree with the thumb test, it caught a bad spot on mine that looked fine from outside. Lining felt solid everywhere except one spot near the front that dented like pressed cork. Turned out flux had run down and chewed it, and I only found it because the paint on the shell above that spot had gone brown and flaky. Patched it with castable and the shell paint stayed fine after that. Check yours for paint discoloration, it tells you where heat has been sneaking through.

Update: ran the thumb test over the whole lining like you guys suggested. Everything feels solid except the spot where the chunk came out, so I packed some castable in there and it set up hard. What I'm still staring at is that pile of crumbs on the ground under the door. Is that just normal spalling or does losing that much lining mean the whole thing needs a reliner sooner rather than later?

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required