Melted down a bucket of old copper wire into ingots, here's what worked

Nov 10, 2026 Last reply: 3 days ago 4 Replies
Jump to replies (4)

Spent Saturday turning a five gallon bucket of stripped wire into ingots and the first couple of pours looked rough. Cracks and little holes all over the surface, plus a sunken dip along the top of each bar. Almost gave up on the whole idea. Turns out most of it was fixable. The holes came from pouring too cool and from air getting stirred in, so I stopped jabbing at the melt and let it sit hot for a few extra minutes before skimming the junk off the top with a steel spoon. A pinch of borax helped pull the nasties out of the melt. The sunken spot on top is just the metal shrinking as it cools, that one isn't a defect at all.



Biggest game changer was warming the molds before pouring. Cold steel was freezing the surface instantly and trapping that cracked, layered look. A few minutes over the forge got the bars coming out clean and shiny. The last three pours look almost store bought, which felt pretty great for scrap that was headed for the recycler.



Going to melt the ugly first bars down and redo them this weekend.


I had similar trouble with tiny pinholes even after trying to keep my melt hotter longer. My scrap was primarily old sheet metal, which always introduced a lot of gasses, making even perfect pours look flawed. I found that the key wasn't just the temperature, but what I added right before I started pouring. I started using a fine mixture of charcoal powder to help burn off residual impurities in the scrap. It made a huge difference in the clarity of the final bar. Also, I made it a habit to scrub the inside of my ceramic crucible with a wire brush and a bit of flux every single time I prepared to melt. You really want that surface spotless to keep from introducing new contaminants. My biggest takeaway was realizing how much surface preparation the container needed to be. It really helped clean up the final results for me.

My expirience with impurities has been less about the heat and more about what I put in the crucible initially. I was running a mix of old electrical components and brass fittings, and the initial pours were full of these tiny, trapped gas bubbles, almost like a million pinholes. After reading about using charcoal to burn off gasses, I tried that, but it didn't totally solve the surface issues. What finally made a difference for me was pre-drying the scrap. I’d take my sorted metal pieces, like copper tubing and brass sheets, and run them through a low oven for about an hour before chunking them up and adding them to the kettle. Any moisture in the metal, even trace amounts, was causing localized explosions and creating those little surface cracks you see. It seemed to be the biggest culprit for me. Another small trick I found useful was changing how I handled the skim. Instead of just letting the impurities float on top and then scraping them, I learned to hold a small piece of wool, like a clean scrap of felt, and gently press it into the melt right at the surface while skimming. It helped pull those oxides and gasses down into the wool and out of the molten metal as I lifted it out. It takes some careful timing, but it cleaned up the surface enough to make the bars usable.

That part about the dip on top being normal is a relief, I thought my bars were ruined too when they sank in the middle. I've only done a couple small melts so far and I'm still guessing at when the metal is ready to pour. Is there a trick to knowing it's hot enought, like a color it should look, or do you just give it extra minutes and hope?

Not buying the wire brush on the crucible part. Scrubbing a ceramic crucible with a wire brush every melt is just going to chip the glaze and knock grit loose, and all that loose stuff ends up right in your pour. I wrecked one that way a while back, ended up with hard dark specks in half a batch of aluminum. A quick wipe out with a rag while it's still warm does more than any scrubbing, and if you really need to clean it, scrape gently with something plastic or wood. Charcoal as a cover makes sense to me, but the scrubbing habit I'd drop.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required