1. Home
  2. ⏣ General Metalworking
  3. Plate Steel hole punch

Plate Steel hole punch

I am looking for a manual/portable hole punch capable of 1/2" holes in 1/4"
plate or angle iron. I saw one mounted on a sign makers truck that used a
long lever and worked great.
I have searched Google and other sites to no avail. Any ideas?
Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
formatting link

Reply to
Teamcasa
Loading thread data ...
What you want is something like a roper whitney Number 20-
formatting link
are still available new, although not cheap. Often available used for $100 - $200, sometimes even less if they dont know what they have. New punches and dies are available in all kinds of sizes and shapes, even square and oval.
Reply to
rniemi
That's it! Thank you very much! Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- ** SPEED ** RETENTION ** COMPLETION ** ANONYMITY ** ----------------------------------------------------------
formatting link
Reply to
Teamcasa

Site Timeline

Related

  • Hydraulic Punch hole size question

  • Hi Gang - In the process of finishing the hydraulic punch and have a question...

  • square punch for styrene ?

  • A punch is good, but for a clean hole you really need a die too, and a way...

  • Greenlee hole punch 2" - anyone got one?

  • Hi all -Does anyone have a 2" diameter round Greenlee manual style punch they...

  • Punch holes with a flypress?

  • I'm wondering what the capabilities are of a couple of flypresses I have -...

  • Making a square hole leather punch

  • Need to make something that punches out, in ~1/16" soft leather, asquare hole,...

  • Punch and chisel gauge question

  • I got a punch and chisel set from HF. With it came a gauge, a "T"shaped affair....

  • punch force

  • Hi All; I'm looking at making a press that will crimp the end of a piece of...

  • One hole straps - hole up or hole down?

  • When running EMT on a wall parallel to the floor and using one hole strapsfor...

  • Roper Whitney #68 Punch

  • Hi,I'm refurbishing an old Roper foot operated punch and have hit...

  • Which one is better? PUNCH PRESS VS LASER

  • I do not run either, but If you need to nibble a hole then the advantage goes to...

  • brass vs bronze for making a punch

  • What if any differences might I notice when making and more importantly using a...

  • Etymological question -- "waller" a hole

  • A center punch makes a small indentation that minimizes the tendency of a drill...

  • Need to punch a 1" Hex hole in 1/2" metal

  • I think one heats the metal and then uses a hammer punch to punch the hole. But...

  • Enlarging anvil hardie hole ?

  • OK heres a nice problem !I have a heap of stakes for use on an anvil with a 1...

  • Punch blanks

  • Brought home a few punch blanks, or raw materials, which are littleround things...

  • center punch

  • a long time ago i was at a friends shop and he had a center punch that hadan eye...

  • center punch

  • a long time ago i was at a friends shop and he had a center punch that hadan eye...

  • DIACRO PUNCH?

  • Hi,Just wanted to let y'all know that I'm selling my Diacro No.2...

  • Best way to drill hole in top plate for conduit. (Revisited)

  • Been trying to drill through that top plate for my 2 inch conduit. Forsome...

  • Drilling a big hole in small steel plate

  • But a Greenlee punch is available to punch the 15/32" hole witha key tab to...

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.