Why do my printed minis keep coming out with chewed up faces?

Nov 18, 2026 Last reply: 1 hour ago 5 Replies

First reply

RafterHank89

Nope, it's not the nature of the beast. Your buddy was on the right track with support tip size, that's the whole ballgame at 28mm scale. The default support tips in most slicers are way too chunky for faces, and when you rip them off a fine detail area you take half the detail…

Read the full reply

Every mini I print ends up looking like it lost a fight with a cat. I'm doing 28mm scale figures on a resin printer, and no matter what I try, the face is the first casualty. The eyes come out blobby, the nose gets these little divots where the supports were, and by the time I've nipped everything off it looks like the guy went ten rounds with Mike Tyson.



I've tried angling the model maybe 30 degrees, moved the supports away from the face onto the back of the head and shoulders, and I'm printing hollow with drain holes now. Still, the front of the face always has some crater or a smeared section where a support tip clung on for dear life.



Is this just the nature of the beast at this scale? My buddy does the same thing with a similar setup and his faces come out smooth as glass, which is driving me a bit mad. He said something about support tip size but I couldn't follow half of what he meant. Do you guys place supports manually, or is there an angle that just works better for heads? Genuinely at the point where I'm considering sculping the faces back with green stuff every single time, which defeats the whole purpose of printing them.


Nope, it's not the nature of the beast. Your buddy was on the right track with support tip size, that's the whole ballgame at 28mm scale. The default support tips in most slicers are way too chunky for faces, and when you rip them off a fine detail area you take half the detail with them. What fixed it for me: drop the tip diameter way down, like 0.2mm or smaller if your slicer lets you, and manually place every support near the face. Auto supports are fine for the body, but they'll happily park a fat tip right on a nose or eyebrow. I go through and delete anything touching the face, jaw, ears, or any detail I care about, then hand place small tips on the underside of the chin, the back edge of the jaw, and anywhere else it's hidden. If a support has to touch somewhere visible, put it where the tip meets a flat or recessed area that you can sand.

On angle, I've settled on 30 to 45 degrees tilted back and slightly to one side, so the face leans into the exposure but the front edge of the face isn't where supports grab. The face being angled too flat to the build plate is often why eyes blob out, because islands and partial cure smear detail. Check the layers in your slicer preview and look at the face specifically, if the eyes are forming as big islands early on, tilt more.

Also, and this is the sneaky one, dial in your exposure time. Slight overexposure makes every tiny feature fatten up and the eyes especally turn to mush. Run a calibration print, get exposure dialed to the minimum that holds detail, and suddenly faces stop looking puffy even before you touch supports.

One more thing, don't yank supports off cold. Pop the minis in some hot water for a bit first, supports come off way cleaner and you don't take craters with them. Between small tips and a warm water removal, my faces come out clean enough that I only ever green stuff genuien print failures.

I chased this same problem for months and the thing that actualy fixed it for me wasn't a setting at all, it was a pair of flush cutters. I used to grab supports with needle nose pliers and pull, which is exactly how you get those divots. Now I snip each support near the base and near the model, then the stubs are tiny and sand off with a light pass of a fine file. Takes an extra minute per mini but the faces came out clean almost overnight. Also agree with the person above about not touching the face with supports, learned that the hard way on a whole squad of guardsmen with cratered chins.

Couple of patches I've used since the days when our exposure settings were pure guesswork and every print was a lottery ticket. If a divot survives anyway, dab a tiny smear of the same resin in it with a toothpick, hit it with the UV light, then sand it flush. Cheaper than green stuff and you can't see it under primer. Also, back when I started we printed everything solid because hollowing was fiddly and we cracked minis left and right. If you're hollow, don't let those drain hole edges sit anywhere on the face, tuck them in shadow gaps behind arms or under cloak edges. Cured resin fills real nice with a fine file and a wet sand, most of my fixes are quieter than that.

I'd push back on the 0.2mm tips advice. Tried that for a while and half my supports just failed to attach or the tip fused into the detail anyway because a tip that thin either doesn't grip or cures into the surface like a wart. What actually worked for me was leaving the tips at a normal size but adding an internal strut angle so nothing load bearing touches the face at all. The fine tips on a hollow 28mm head are carrying way too much weight for a whole print session, so they either fail or they dig in. Move the weight to the back and the tip size stops mattering much.

One thing I never see discussed is how dirty the wash alcohol gets before it actually ruins your surface detail. Mine went off subtly, and for weeks I blamed my supports and orientation when the real culprit was a film of uncured resin left drying on every face, wich slightly blurs the fine stuff like eyelids and nostril rims before you even cure it. I now run two baths, a rough first dip and a clean final one, and rotate in fresh alcohol far more often than feels economical. Since doing that the surfaces come off the printer looking crisper, and honestly some of what I was calling blobby eyes was probaly this the whole time.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required