ARM: Review - Panda 1/35 scale Russian 2S6M Antiaircraft Artillery

Kit Review: Panda 1/35 scale Kit No. 35002; Russian 2S6M Tunguska Anti-Airc raft Artillery; 1,220 parts (613 in olive styrene, 512 in light brown styre
ne, 94 etched brass, 1 length of twisted copper wire); retail suggested pri ce US$80.00
Advantages: first kit of this vehicle in this scale in styrene; beautifully done rendition of the main production model of the vehicle; includes two 9 M311 ?Treugol?nik? missiles for display
Disadvantages: a large number of ultra-tiny parts will discourage many mode lers
Rating: Highly Recommended
Recommendation: for all Soviet and Russian modelers and Antiaircraft fans
    Back in 1987 I was working in the 3rd Armored Division G-2 shop in Frankfu rt, Germany, and had recently been the first person to model the then new T -80B and T-80BV tanks. But now we were getting pictures of a rather odd veh icle moving into East Germany under tarps that was the size of a large self -propelled artillery piece with a very bulky turret. I was asked if I could also model this new vehicle and I agreed once we could figure out what it was and what it did.
    It soon became apparent that this was the legendary ?ZSU-X? which had appeared in the Pentagon?s ?Soviet Military Power? annual reports for several years. But whereas that had supposed this was using a T-72 chassis , the visible parts showed it to be using a Tomashov designed chassis relat ed to the SA-4 GANEF and 2S3 ?Akatsiya? howitzer. We finally got some c learer photos and I went to work.
    We had problems figuring out how many guns it had ? two were visible but wear marks on the canvas showed four muzzles, two per side. We could also see what looked like four missile tubes. Reports soon indicated it was dubb ed ?Tunguska? (a river in Siberia) and did use both missiles and 30mm c annon. It had a target acquisition radar like the SA-8 that popped up in th e back and a fire control radar on the front of its turret. We also found o ut it had a suspension that could be dropped down to 10 cm for stability wh en firing and using the search radar for more precision.
    The Soviets finally paraded the vehicle, and we found out it was dubbed th e 2S6. Armament consisted of two 2A38 twin-barreled 30mm guns and four 9M31 1 ?Treugol?nik? missiles. The later, full production 2S6M variant the n added four more for eight missiles onboard. I did scratchbuild the model and USAREUR made an unclassified training poster of it just before I left Germany in 1989.
    The Tunguska is a very impressive vehicle, as it is fully computer control led and will select missiles, guns/missiles, or guns as it deems necessary to eliminate threats. It uses a velocity sensor on the outside barrel to de termine shell velocity and correct for it using the fire control radar. The guns are fired in 20-40 rounds (5-10 rounds per barrel) bursts and are ver y powerful, with the cyclic rate being so high flames from still burning pr opellant shoot about a meter out of the shell ejection ports when it fires. The missile has two stages ? a very high acceleration first stage and an unpowered second stage that continues to the target on inertia at very hig h velocities of over Mach 2.5.
    There have been a few resin kits of this vehicle produced up until now but were complex and difficult to assemble at best and impossible at worst. No w Panda, another of what seems to be an unending stream of new model compan ies coming from China, has produced a kit of the main production variant, t he 2S6M. This is a new mold kit as there is nothing that it could be based upon, and Panda has done a nice job of it.
    This is a very complex kit and rivals the DML Tiger I kits for sheer numbe r of parts. The price is high ? I managed to get this one for $60 at AMPS 2013 and lower prices are seen on the Internet ? but that is the cost of today?s super-detailed kits with etched brass and single link tracks.
    The kit has some options but setting the suspension height is not one of t hem. The suspension units (parts D21-25-27-28) are keyed so the road wheel arms will only attach at the proper movement angle. The tracks will be a bi t of a pain as each link consists of a pad and a separate delicate tooth fo r it.
    All of the hull hatches are separate parts but Panda does not offer any in terior or any directions as to which is which. The turbine APU exhaust hatc h (parts A37-B28-B73/74) can be either closed for movement or open for oper ation (it produces about 18 kilowatts of power for the electronic systems). The turbine intake (part A38) and others have etched brass grilles for the m.
    The turret consists of three main parts (AA, BB, CC) and are the base for all the remaining details. Each of the 2A38 cannon consists of 17 parts eac h with the velocity sensors taking six of those (parts B81, C40/41 and D13) with another 21 for the elevating mount. Many of the eentsy parts go on th e guns and radar, so be prepared to use a lot of patience on them.
    The 9M311 missile containers are much simpler and only take 16 parts each (times eight). Note that each side of the turret is assembled separately an d takes six steps in the directions.
    There are another 23 parts to the HOT SHOT search radar and it is quite de tailed.
    The two Treugol?nik (triangle) missiles are provided for display but can not be used as part of the model without major surgery to the launch tubes as they are sealed units.
    One finishing option is provided for a simple protective green vehicle wit h Guards badges and white trim, but these vehicles are often seen with thre e-color camouflage and 6xx side numbers in tank and motorized rifle divisio ns (now brigades). A set of decals is provided with a ?number jungle? f or the bort numbers and also the Guards badges.
    Overall this is a very complex kit but will build up to an accurate model of a 2S6M as in service today.
Cookie Sewell
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

Polytechforum.com is a website by engineers for engineers. It is not affiliated with any of manufacturers or vendors discussed here. All logos and trade names are the property of their respective owners.