Control systems?

Could someone give me a brief summary of the pros and cons of the various methods of providing power and control to model trains? I.E., basic transformer vs R/C, DCC, command control and whatever else may be available.

This would be for use with an outdoor G scale layout, if that makes any difference.

=CB=87

Reply to
raydunakin
Loading thread data ...

Run like Hell! You've just restarted a perennial debate :-).

Reply to
Larry Blanchard

Heheh. Well, how about this instead... a list of each method's features? I need some way to get a handle on what these different systems can (and can't) do.

Reply to
raydunakin

Well, I'm a DCC bigot, so just to get the debate started, I'll say DCC can do *everything* better! :-)

All seriousness aside, I'm not sure I'd want to trust the rail/wheel electrical contact of an outdoor railroad, so I think that I'd personally tend to look at R/C and on-board batteries first.

But why not talk to these folks, or other similar groups, to get some first-hand experience?

formatting link
HTH, Stevert

Reply to
Stevert

Like waste your money?

Reply to
Greg Procter

There are four main possibilities:

- Analogue through the rails.

- DCC through the rails.

- Radio control with batteries on the train.

- Radio control with 12/18 volts on the rails.

A basic problem with analogue control is that the voltage varies - the higher the voltage, the better it finds it's way between rail and wheel. Solution: PWM controller.

DCC costs money. Probably ideal for garden railways where you just want to switch between trains.

Radio control works well, but rolling stock loaded with batteries severely limits the pulling power of locos.

Radio conntrol utilizing full voltage on the tracks works better but I'm not sure it has advantages over the right DCC system ( = $$$)

Regards, Greg.P.

Reply to
Greg Procter

Thanks Greg!

Reply to
raydunakin

I guess that 30 or 40 cars is a severe limit!

Wander over to

formatting link
and check their forums. This is specifically G scale. Particularly the General Forum. Lots of postings discussing battery power. Most with separate battery cars, others with battery in locomotive.

Big advantage of battery power, is that you can use cheaper track (ie wood or brass) as there is no need to keep it "electrically clean".

Disclaimer. I am using DCC for outdoor G scale.

Reply to
Robert Small

Greg Procter wrote in news:43CCBF25.4320BA1 @ihug.co.nz:

THere is also the possibility of doing a wireless DCC with batteries on the train. But I don't know of anyone who makes the gear.

Reply to
Gordon reeder

How about live steam with RC? They do that already. Bruce

Reply to
Bruce Favinger

I'm sure everyone will tell us I'm wrong ;-)

Regards, Greg.P.

Reply to
Greg Procter

How would that work???

Would you transmit a DCC signal by radio?

Reply to
Greg Procter

Greg Procter wrote in news: snipped-for-privacy@ihug.co.nz:

Generaly yes, that was the idea. But now that I've given it some thought I see that it is a bit more complicated. First: THe power source can not be DC. DCC uses square wave AC power. There goes the idea of a simple battery to power the locomotive.

Second: You would need to separate the DCC control signal from the DCC power. Actually this may not be that difficult if you take the signal from the control bus, between the cab and the booster.

Trying to kludge a DCC system into a wireless system with DC power is probably not a good way to go. But if a manufacturer were to market a purpose built decoder with a radio link that could run on DC power... Now that would be somthing. And very feasable.

Reply to
Gordon reeder

Which is essentially the same, radio control with batteries, using DCC as part of it allows some common components, such as decoder. The radio reciever needs to deliver the dcc signal to the decoder which can get its power from a battery. See

Keith

Reply to
Keith

OK, I have a few more questions about control systems...

  1. Who makes R/C systems for trains?

  1. What kind of batteries do the R/C systems use, how do you charge them, how long do they hold a charge, and how long will the battery last?

  2. How much problem is there with radio interference when using an R/C system?

  1. With either R/C or DCC, would I be able to use the loco's existing sound/lights/smoke?

  2. From what I've seen so far, DCC seems a bit complex. Could a visitor who is unfamiliar with the system be able to run trains with me? Could a child run it?
c
Reply to
raydunakin

No, a battery would be fine! Transistor switching is capable of producing the square wave AC.

They are one and the same thing - no problem!

True.

Reply to
Greg Procter

Greg Procter wrote in news:43CF64EC.BDC2C6B3 @ihug.co.nz:

Sure it could be done. But that adds one more thing that can fail. A purpose built DCC controler could be designed with an 'H-Drive' motor control. THat would allow the motor to be controled in either direction with a simple DC source.

Reply to
Gordon reeder

YES!

Reply to
Greg Procter

OK, I have a few more questions about control systems...

  1. Who makes R/C systems for trains?

  1. What kind of batteries do the R/C systems use, how do you charge them, how long do they hold a charge, and how long will the battery last?

  2. How much problem is there with radio interference when using an R/C system?

  1. With either R/C or DCC, would I be able to use the loco's existing sound/lights/smoke?

  2. From what I've seen so far, DCC seems a bit complex. Could a visitor who is unfamiliar with the system be able to run trains with me? Could a child run it?

I posted these questions earlier but they seem to have gotten lost in the shuffle.

Reply to
raydunakin

I don't think they got lost, I just think no one answered because there is no such product. You can certainly do it, but you will have to cobble together a system from existing airplane and model car systems and adapt it yourself to your model railroad application.

From the text of your question ". . . sound/lights/smoke . . ." it sounds like you are running O gauge tinplate with AC track power. You can use DCC with tinplate, but you need to get answers from other tinplaters who have adopted DCC to operate their trains. A good place to go in addition to this board is the Digitrax users forum. You can find it on Google.

Froggy,

Reply to
Froggy

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.