AMS6455

i posted this before, but for some reason, i never saw it on the
group.
looking for 1" by 100 ft of 0.014-0.016 with a Rc of 42 -47 .
help!
its an old standard and i can't find this stuff anywhere.
i'd need paperwork, if possible.
the spec analysis is:
C .48-.53
Mn .70-.90
P .040
Si .20-.35
Cr .80-1.10
V .15 min
i figure that someone must have some... somewhere.
Reply to
beav
Loading thread data ...
Google Groups: sci.engr.metallurgy AMS6455 help. Folks, I'm pulling my hair out trying to find a specific alloy, whether its a sheet or a one inch wide slitted roll of any length. ... groups.google.com/group/sci.engr.metallurgy - 56k - Cached - Similar pages
Steel, Sheet, Strip, and Plate 0.95cr 0.22v (0.48-0.53c) (SAE 6150) Document Number:, AMS6455. Revision Number:, H. Date Published:, July 2001. Title: Steel, Sheet, Strip, and Plate 0.95cr 0.22v (0.48-0.53c) (SAE 6150) ...
formatting link
- 25k - Cached - Similar pages
Products 6150, AMS6455. 8735, AMS6357. 8740, AMS6358. AERMET 100, AMS6532, AMS6532, AMS-6532. 17-22A, AMS6385, 6436. X200, AMS6406. H-11, AMS6437 ...
formatting link
- 121k - Cached - Similar pages
Aeronautical Systems Center - Engineering Directorate SAE-AMS6455, STEEL, SHEET, STRIP, AND PLATE 0.95CR - 0.22V (0.48 - 0.53C) (SAE 6150), 3/17/1989, IS, 9515, ADOPTION NOTICE 17 MAR 89. ... engineering.wpafb.af.mil/engstds/reports.asp?Reportchoice=72 - Similar pages
Maybe one of the two companies has it. Martin
Martin H. Eastburn @ home at Lions' Lair with our computer lionslair at consolidated dot net NRA LOH & Endowment Member NRA Second Amendment Task Force Charter Founder IHMSA and NRA Metallic Silhouette maker & member
formatting link

beav wrote:
Reply to
Martin H. Eastburn
whether its a sheet or a one inch wide slitted roll of
I KNEW my original post was out there, somewhere.
Title: Steel, Sheet, Strip, and Plate 0.95cr 0.22v
this is just the sae standard
AMS-6532. 17-22A, AMS6385, 6436. X200, AMS6406. H-11,
yeah. i went to them and they "no quoted" me. this is when i realized that i was up a creek without a paddle.
6150), 3/17/1989, IS, 9515, ADOPTION NOTICE 17 MAR
the Wright Patterson AFB engineering standard
i appreciate the effort, but these are avenues i've pursued.
say.... on the SAE standard, are they saying that SAE6150 is the SAE equivalent to tthe AMS material?.....this could be really helpful...
off to google! > > > >beav wrote: >> i posted this before, but for some reason, i never saw it on the >> group. >> >> >> looking for 1" by 100 ft of 0.014-0.016 with a Rc of 42 -47 . >> >> >> help! >> >> its an old standard and i can't find this stuff anywhere. >> >> i'd need paperwork, if possible. >> >> the spec analysis is: >> >> C .48-.53 >> Mn .70-.90 >> P .040 >> Si .20-.35 >> Cr .80-1.10 >> V .15 min >> >> i figure that someone must have some... somewhere. >> > >
Reply to
beav
WAHOOOOOO! SOURCES EXIST!!!!!
SAE6150 is REALLY close. the P value is tightened over the AMS6455. the Si value is a little looser than the AMS number. there are at least two supppliers of 6150. as long as their Si analysis figure falls in line with 6455, i'm golden.
thanks for making me look again Martin.
Reply to
beav
For anyone that cares, all i ever found were dead ends.
In an amazing coincidence, another part that we had records on listed the SAE 6150 material, and included a source.
Sure enough, they had it. I need about 100 pounds, and the minimum buy is 1500 pounds... close enough. I'll take it!
The source is Elliot Bros
Reply to
beav

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.