PRO/Engineer (Creo) discussions

Intralink 3.3

I know I'm way behind the rest of you on Intralink, but that could help me because I know you all have the answer I'm l...

15 comments posted 21yrs

posted by fmcdougle

15 comments posted 21yrs posted by fmcdougle

3D models of pallet rack components?

Anyone have reasonably accurate models of warehouse pallet rack system components? You know . . . the uprights with hol...

0 comments posted 21yrs

posted by sporkedUNDERLINEagainMUNGE

0 comments posted 21yrs posted by sporkedUNDERLINEagainMUNGE

composite datum curves

I have several datum curves and would to connect all of them into one curve. I am using Wildfire 2.0. this process used...

4 comments posted 21yrs

posted by gamig

4 comments posted 21yrs posted by gamig

Laser printer line weights

How do I control the line weights for geometry, dimns, etc. when using a laser printer? Cheers, Sean

3 comments posted 21yrs

posted by s.p.kerslake

3 comments posted 21yrs posted by s.p.kerslake

Flaring, fogging and scattering - advanced rendering functionality

Anyone out there care to explain how the advanced rendering functionality such as lens flare, light scatter and fog eff...

0 comments posted 21yrs

posted by antrachite

0 comments posted 21yrs posted by antrachite

NEW PRO/ENGINEER WILDFIRE 2 - EXCELLENT OFFER !!

-|> WORLDWIDE FREE DELIVERY -|> EASY AND FAST ORDERING -|> PLEASE WRITE AT: snipped-for-privacy@hotpop.com -|> VERY BIG...

2 comments posted 21yrs

posted by raitorob

2 comments posted 21yrs posted by raitorob

PROE/ DRAFTER-DETAILER/ CONTRACT/ IN

OMNI GROUP 419-380-8853 snipped-for-privacy@buckeye-express.com PROE/ DRAFTER-DETAILER/ CONTRACT/ IN We need two ProE D...

0 comments posted 21yrs

posted by tgugger

0 comments posted 21yrs posted by tgugger

Pro/INTRALINK 3.4?

Have anyone of you checked out the new version of Intralink? Was looking for any opinions, first impressions... Thanks T...

1 comments posted 21yrs

posted by tim607

1 comments posted 21yrs posted by tim607

changing dimension decimal places changes tolerance values.

~In rel. 2001 if you set a dimensions tolerances differently to the default ones, and later change the decimal places f...

0 comments posted 21yrs

posted by david.bower

0 comments posted 21yrs posted by david.bower

Small irritations with PRO E

Hi, I've been using PROE happily for quite some time... but there is a few small irritations which I dun seem to be abl...

2 comments posted 21yrs

posted by elvin82nospam

2 comments posted 21yrs posted by elvin82nospam

Windchill PDMLink w/ Solidworks

Anyone use PDMLink with Solidworks? I'd like to hear any stories good or bad of your experience.

0 comments posted 21yrs

posted by someone

0 comments posted 21yrs posted by someone

Consistent units throughout assembly.

Is there a method to make all the components in an assembly have consistent units. I have hundreds of components in the...

1 comments posted 21yrs

posted by solid3ddesigns

1 comments posted 21yrs posted by solid3ddesigns

Memory error

Well, on several winxp machines with 2 gig of RAM we have problem with Pro/ENGINEER memory error while opening master r...

9 comments posted 21yrs

posted by dida128

9 comments posted 21yrs posted by dida128

SNAP LINES

A drawing I'm working on will insert vertical snap lines but no horizontal ones when I do a dimension clean up. Anyone e...

4 comments posted 21yrs

posted by david.bower

4 comments posted 21yrs posted by david.bower

Mass Analysis

Hi A have a question about the inertia tensor calculated in Pro Engineer. The tensor is shown with Ixy, Ixz etc. But th...

0 comments posted 21yrs

posted by Spier75

0 comments posted 21yrs posted by Spier75