General Robotics Forum

New product makes logic design easy

Hello everyone. If you are interested in new ways to develop FPGA based logic, where signals and data can be viewed and...

6 comments posted 20yrs

posted by andy.ward

6 comments posted 20yrs posted by andy.ward

Low cost vision system, thoughts

I was thinking about this last night, I've had in the back of my mind an idea for a low cost vision system. What is req...

25 comments posted 20yrs

posted by mlw

25 comments posted 20yrs posted by mlw

30 Gauge Wire & DC Motor?

I was wondering if I can use 30 gauge wire-wrapping wire to power a DC motor. The motor is a "Gear Motor 2" from www.ho...

3 comments posted 20yrs

posted by redbrickhat

3 comments posted 20yrs posted by redbrickhat

Bluetooth link to replace serial cable for OOPic

Hi, I have an oopic II+ microcontroller with RS232 level converters and I am currently programming it with a serial cab...

6 comments posted 20yrs

posted by niamhom

6 comments posted 20yrs posted by niamhom

Differential (or is it?) question

I need a gearset like a differential, except that I want each axle to rotate in the opposite direction. Right wheel rot...

2 comments posted 20yrs

posted by Ramon

2 comments posted 20yrs posted by Ramon

IBM PC Parallel port desc

I know this is not much more than a google away, but if you are looking... http://www.linuxpcrobot.org/?q=node/5

0 comments posted 20yrs

posted by mlw

0 comments posted 20yrs posted by mlw

Software-only USB driver for AVR

The following press release may be interesting to readers of this news group because it presents a complete solution fo...

1 comments posted 20yrs

posted by avrusb

1 comments posted 20yrs posted by avrusb

Robotics crypt? Expectations?

In another thread, someone mentioned that robotics seems in the decline. While I agree, I also wonder why. Maybe it is...

7 comments posted 20yrs

posted by mlw

7 comments posted 20yrs posted by mlw

Using I2C

Hi, all! I'm trying to read from a Sensor which speaks I²C, but I have many problem... The Sensor is attached to the pa...

5 comments posted 20yrs

posted by lucabert

5 comments posted 20yrs posted by lucabert

control of 24vac motors?

I'm pretty new to electronics and was wondering what it would take to control two 24AC motors on a pan/tilt head with 1...

2 comments posted 20yrs

posted by joe_d_builder

2 comments posted 20yrs posted by joe_d_builder

Use of rat brain cells as a processor

For a while now I have been wondering what everyone else thought of this. A little less than a year ago I believe, an a...

1 comments posted 20yrs

posted by PenJones128

1 comments posted 20yrs posted by PenJones128

flexible wire that becomes ridged muscle wire?

hello all. new to the group. i've been searching for a while now but still not found what i'm looking for. i know of a...

0 comments posted 20yrs

posted by corpseguy

0 comments posted 20yrs posted by corpseguy

the crypt

Hi, I've read comp.robotics.misc for many years but almost never post, although I did get some good help last year from...

67 comments posted 20yrs

posted by dpa

67 comments posted 20yrs posted by dpa

Need a controll board for 3 servos

I need to make a controll board for 3 servos by regular potentiomenters. The problem I have - I do not know nothing abo...

6 comments posted 20yrs

posted by bad

6 comments posted 20yrs posted by bad

An invitation to join RoboMontreal

Attention Montreal-Area Roboticists! Come and check out the first forum dedicated to robotics enthusiasts in the Montre...

0 comments posted 20yrs

posted by donald.dansereau

0 comments posted 20yrs posted by donald.dansereau