⚗ Material Sciences

Chemical ratios in Epoxy

Hello I've been trying to track down a general idea of the chemical ratios in "epoxy" (ie C:H:O:.. etc). While it seems...

1 comments posted 22yrs

posted by Anthony.Faust

1 comments posted 22yrs posted by Anthony.Faust

Silver, dielectric constant, data

Hello, i need to get data concerning the optical properties of silver in infrared and far infrared. Reflectance measure...

0 comments posted 22yrs

posted by dseibel25

0 comments posted 22yrs posted by dseibel25

Surface lab Manager position at Micron Technology has been filled

Our response to this position was great. I want to thank everyone who submitted their resume. We have filled the positio...

0 comments posted 22yrs

posted by mmburks

0 comments posted 22yrs posted by mmburks

Barium Fluoride Crystals? Need ID.

I have approximately 1,100 crystals (rectangular, 8mm X 20mm X 45mm) that I believe are barium fluoride. They were spar...

1 comments posted 22yrs

posted by greg

1 comments posted 22yrs posted by greg

Transparent high temp material needed

i need to design and manufacture a transparent window in batches of a few hundred at a time apporox 30mm x 20mm x 5mm t...

0 comments posted 22yrs

posted by featuretree

0 comments posted 22yrs posted by featuretree

Diamond synthesis - BBC2 4 March

Horizon tells the story of the diamond labs. Thursday 4th March, 9pm, BBC Two, UK. BBC World afterwards. No other infor...

0 comments posted 22yrs

posted by DavidM

0 comments posted 22yrs posted by DavidM

heat exchangers

I am looking for a material that is able to conduct heat from a hot metalic surface and can transfer the heat to create...

2 comments posted 22yrs

posted by nickkulenkampff

2 comments posted 22yrs posted by nickkulenkampff

Carbon nanotube

Dear guys; As you know most of the polar solvents are known good solvents for carbon nanotubes. But actually I wonder wh...

0 comments posted 22yrs

posted by E_Najafi

0 comments posted 22yrs posted by E_Najafi

Effect of forging methods on tensile strength of aluminum alloy 2618

I found in Metals' handbook that forgings normally have lower tensile and yield strength compared to typical products,...

1 comments posted 22yrs

posted by nnriverside

1 comments posted 22yrs posted by nnriverside

portland cement classification

How is the quality of portland cement classified?

1 comments posted 22yrs

posted by ninebagmix

1 comments posted 22yrs posted by ninebagmix

Interesting Petroleum Website

Note the following interesting education petroleum crude oil website: www.onta.com www.texasrawcrude.com Click on the ab...

0 comments posted 22yrs

posted by julian1967

0 comments posted 22yrs posted by julian1967

information about sheet metal...

Hi there Can anybody please inform me about hard sheet metal(: such like Tungsten Carbide) of which thickness is not exc...

2 comments posted 22yrs

posted by may1974

2 comments posted 22yrs posted by may1974

Best material for low permeability flexible tubing?

Hello, I hope I am posting this to the right group. I am looking for material advice for 1/8" ID flexible tubing for in...

3 comments posted 22yrs

posted by flyerx_2000

3 comments posted 22yrs posted by flyerx_2000

Dissolution of PLGA in dichloromethane

Hi, here is a dumb question from a molecular biologist I am trying to dissolve PLGA (ratio 50:50, 65:36, 75:25 and 85:1...

1 comments posted 22yrs

posted by amelie.desautels

1 comments posted 22yrs posted by amelie.desautels

plastic selection help please

I'm looking for a plastic film / sheet material as follows: thickness: approx. 2 mm / .075" color: black, completely op...

1 comments posted 22yrs

posted by groundzero

1 comments posted 22yrs posted by groundzero