Looking for Uncommon Threading Die

I'm looking for a threading die for garden hose fittings. I think this might be 5/8"x14 NPT. All the standard tap and die sets skip over this size. Doesn't have to be particularly good quality, carbon steel would be okay, just want to chase threads on an old faucet that has developed mineral deposits to the point that I can't get a hose to screw on anymore. The faucet is otherwise in good working order, and I hate to have to replace it just because it needs cleaned up a bit. The folks who make these parts have to have taps and dies, right? So what are they using and where do they get it?

Reply to
Ol' Duffer
Loading thread data ...

Sounds like an job for a thread restoring file at or close to the thread size. Why not see if you can borrow one or find a place where you can buy just one file covering the pitch you need. Here's some:

formatting link
The ones I've got cover eight different pitches per file, they are square in section and have four on each end.

Another thought, how about wrapping and tying a bit of rag around those cruddy threads, soaking it with vinegar and then using a rubber band to secure a small plastic bag around it to keep the vinegar from evaporating. Leave it that way for a day or so. You may well find that the mineral deposits soften enough so you can easily remove them with a wire brush.

HTH,

Jeff

Reply to
Jeff Wisnia

Suggest you first try one of the bathroom cleaners (Limeaway, etc) to remove the deposits from the faucet's threads. You may have to soak some of it up into a sponge or rag and tie it to the faucet. Keep it saturated for a while and see if it attacks the deposits. Judicious use of a threadfile might help also. After the faucet is clean, screw on a garden-hose quick disconnect female and a corresponding male part on the end of the hose.

Bob Swinney

Reply to
Robert Swinney

What if you take a junk female hose fitting and cut some axial lines in it with a hacksaw? Not through cuts, just scoring cuts, enough to leave some sharp edges to act die-like. Then just try threading it on, maybe the saw cuts would do the job for you.

Another idea is a spot blaster tool with some glass bead media.

There is no thread 5/8-14 NPT that I know of. 'Course, I don't know everything, not by a long shot, nor have I researched this. Also, *my* pipe fittings are a lot bigger than 5/8".

There exist thread files for NPT threads, oddball thread counts like 11½. I own one. Those would work OK for you although it's super-hard to file something perfectly round..

GWE

Reply to
Grant Erwin

A male garden hose fitting on my bench is 1.050 over the threads, pitch is 11.5 TPI. That's probably nominally 1-1/16 - 11.5. I think I have seen dies like this in a catalog, but I lathe-cut them.

You should be able to clean up your faucet with a mild acid (vinegar or dilute muriatic) or a household lime remover. A brass wire brush may help.

Reply to
Don Foreman

I think it is first not a taper, since it has a washer, and my hose fittings are more like an inch

Reply to
yourname

You can clean up male threads pretty well with a triangular needle file.

jw

Reply to
jim.wilkins

1.050 is the nominal OD of 3/4" pipe. Coincidence?

Ted

Reply to
Ted Edwards

Further research leads me to believe that 1.0625 x 11.5 is in fact the correct size. Although mine are definitely tapered, but that's old school, and no harm would be done by rethreading to the current straight standard. Do you remember what catalog you saw this size in? Obviously, it's going to be tricky to chuck my house up for turning, which is why I am looking for a hand die ;-) Thanks for the info.

Reply to
Ol' Duffer

Just close enough to get you in trouble, since 3/4" NPT has

14 threads per inch, but as I am learning, garden hose (GHT) has 11.5 threads per inch. If you did manage to get the threads to grab, it would mess them up and probably still leak.
Reply to
Ol' Duffer

Sorry, I don't -- and I looked.

Reply to
Don Foreman

Well, thanks for looking. I did find a 1-1/16 x 12 TPI die at McMaster-Carr, which is almost close enough - maybe if I fired up my dremel and ground out most of its threads... Or maybe, I'm thinking, if I get a 1" NPT conduit coupler, which happens to be 11-1/2 TPI, cut some wide saw kerfs and hammer it down to size...

Reply to
Ol' Duffer

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.