⏣ General Metalworking

30777 Threads Posts
to

ASONG AS-235 x-axis

I recently purchased a series 1 type mill. It came with a ASONG AS-235 x-axis drive. I don't believe it is properly ins...
0 comments posted 21yrs
posted by jlacombe
0 comments posted 21yrs posted by jlacombe

What steel to use?

I know about CRS, O-1 and D-2 that I have used for years. I have an application to make a part that will be 6" long, 1"...
5 comments posted 21yrs
posted by tom(nospam)
5 comments posted 21yrs posted by tom(nospam)

Smithy Bearings Again

I posted this question before into a hurricane (as it were) of posts about the gov'ment and New Orleans; normally I wou...
5 comments posted 21yrs
posted by tim
5 comments posted 21yrs posted by tim

Recommendations for clamp wire temper

I'm looking for some general recommendations for quality steel wire to use as wire for making clamps, a la the Clamp-Ti...
6 comments posted 21yrs
posted by benh
6 comments posted 21yrs posted by benh

TerraLUX MiniStar LED kit for MiniMag review

I got my LED kit about a week ago in the mail. I've been using it at work all this week. http://www.luxeonstar.com/item...
12 comments posted 21yrs
posted by lasernerd
12 comments posted 21yrs posted by lasernerd

db meter?

Anyone got a clean db meter they don't need and want to sell/trade? I live about 100 yards from a large freeway that th...
11 comments posted 21yrs
posted by grant
11 comments posted 21yrs posted by grant

Stainless Steel Sheets

I'm in Maryland and am looking for sheets of 20 guage stainless steel. I need one 52" x 13" sheet and two 16" x 32" shee...
5 comments posted 21yrs
posted by rdadams
5 comments posted 21yrs posted by rdadams

Tool reviews

Hello All For lack of anything better to do I have started a review page on some tools that I have bought recently. The...
0 comments posted 21yrs
posted by machineman
0 comments posted 21yrs posted by machineman

Finding smallest circle that fits over a trapezoid

I'm trying to figure out how to calculate the smallest circle that will fit over a trapezoid. No, it not home work -- I...
10 comments posted 21yrs
posted by signalferret
10 comments posted 21yrs posted by signalferret

RE engine turned finish

Thanks Folks for all the suggestions. When you only need to do a few it doesn't matter much exactly how you get the job...
1 comments posted 21yrs
posted by etpm
1 comments posted 21yrs posted by etpm

spring steel ?

Can A36 be spring tempered? If so how well does it perform compared to 5160? Or should i just keep looking for a local s...
2 comments posted 21yrs
posted by sbrowder
2 comments posted 21yrs posted by sbrowder

Charging Drill Motor Batteries

Please excuse this post for being on-topic. I'm of the opinion that it is bad for NiCad batteries to be "ON CHARGE" con...
6 comments posted 21yrs
posted by nospam
6 comments posted 21yrs posted by nospam

Harbor Freight TIG Welder (Gas Line)

I picked up a TIG unit from HF's markdown table. However, the supplied hose for the gas supply won't fit my (standard)...
4 comments posted 21yrs
posted by jdellafera1
4 comments posted 21yrs posted by jdellafera1

radiator fitting question

I took the radiator out to have a leak fixed. Put it back in. The lower oil cooler line as I was tightening it felt lik...
4 comments posted 21yrs
posted by stryped
4 comments posted 21yrs posted by stryped

What is it? LXXIX

Just added another post: http://puzzlephotos.blogspot.com/ Rob
24 comments posted 21yrs
posted by rhvp67
24 comments posted 21yrs posted by rhvp67