⏣ General Metalworking

30777 Threads Posts
to

Lathe carriage stops?

I would like to know if I can buy some gizmo that can provide a definite, positive stop to the lathe carriage before th...
28 comments posted 21yrs
posted by ignoramus18741
28 comments posted 21yrs posted by ignoramus18741

Tailstock Ram side play

I'm running a 40 yr old South Bend 10L. As is common with this type of lathe the tailstock ram is locked with a side lo...
3 comments posted 21yrs
posted by bwjarandall
3 comments posted 21yrs posted by bwjarandall

Motor oil in lathe gearbox

I have a large Monarch lathe built in 1944. It has a geared head,a plain bearing spindle and some sort of oiling pump t...
8 comments posted 21yrs
posted by sbaer
8 comments posted 21yrs posted by sbaer

WAY OT:Cannot delete virus

I've been a beating myself up over a virus in this 'puter most of the day. Norton 2005 detects but cannot delete the vi...
48 comments posted 21yrs
posted by karltownsend.NOT
48 comments posted 21yrs posted by karltownsend.NOT

V-Belt question

Is M-23 V-belt is the same as 3L230 and M-25 is the same as 3L250 I understand that section is the same it's just the r...
4 comments posted 21yrs
posted by alexkuzn
4 comments posted 21yrs posted by alexkuzn

Hour meter

Hi Roger, this is Steve Young - I bought the Taylor Dunn cart a couple month's ago. Was wondering if you had a 2" diame...
11 comments posted 21yrs
posted by stephen
11 comments posted 21yrs posted by stephen

Carcomputing -matalworking=case and brackets

I'm retiring my Dodge van and replacing it with a Ford extended with a V-10! (I'm gona get my share of gasoline before...
2 comments posted 21yrs
posted by tom(nospam)
2 comments posted 21yrs posted by tom(nospam)

OT-Very OT-Geen Fruitcakes in action

An email forwarded from an old and dear but green as alge friend "Dear Friend, No one voted on Election Day to destroy...
126 comments posted 21yrs
posted by gunner
126 comments posted 21yrs posted by gunner

Fitting piston rings

Hi, I need to fit piston rings to an old Wolseley single cylinder engine. I've removed the piston and have the new ring...
25 comments posted 21yrs
posted by cdt22
25 comments posted 21yrs posted by cdt22

Bar folder questions

Hello friends, I'm needing a short sharp right angle bend in some 18" wide sheetmetal and bought an old Roper Whitney b...
3 comments posted 21yrs
posted by siralbabin
3 comments posted 21yrs posted by siralbabin

More of my cheap auctions-

check em out: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=7512724298&rd=1&sspagename=STRK%3AMESE%3AIT&rd=1...
4 comments posted 21yrs
posted by jcataldo
4 comments posted 21yrs posted by jcataldo

Aluminum Bronze questions

Hi Folks, I'm just an amature at casting of metals, and would like some info about alloying copper and aluminium. When...
5 comments posted 21yrs
posted by fcccsales
5 comments posted 21yrs posted by fcccsales

embossing computer case

Hi everyone, Before I ask my question, I would just let you all know I know nothing about metal work. I have a computer...
22 comments posted 21yrs
posted by gautam.bakshi
22 comments posted 21yrs posted by gautam.bakshi

designs for a better shop crane?

I use an engine hoist in my shop to move machines around. I originally rented them as I needed them for about $35/day b...
15 comments posted 21yrs
posted by grant
15 comments posted 21yrs posted by grant

OT Ford adhesive-removal of

Just discovered the rear quarter window on my '95 Ranger PU uses four threaded studs to hold the window gasket to the b...
9 comments posted 21yrs
posted by rhull
9 comments posted 21yrs posted by rhull