General Robotics Forum

Mini VGA Monitor, battery powered

Do you know such thing? If possible, it must be cheap, small (4 to 7 inches screen) and possible to be powered out of DC...

10 comments posted 20yrs

posted by padu

10 comments posted 20yrs posted by padu

Neptune 2

just aquired a Neptune 2 robotic arm, anyone have any info or tel numbers for manufacturer, much appreciated, jim

0 comments posted 20yrs

posted by j.coggan

0 comments posted 20yrs posted by j.coggan

New periodical on robots

Does anyone here know anymore about this magazine? http://www.emediawire.com/releases/2005/10/emw297702.htm Joe

5 comments posted 20yrs

posted by joecoin

5 comments posted 20yrs posted by joecoin

Call for Contribution: RoboCup@Home 2006

Apologies if you receive multiple copies CALL FOR CONTRIBUTION ********************************************************...

0 comments posted 20yrs

posted by tijn

0 comments posted 20yrs posted by tijn

Huh? DAPRA GC was not a good thing?

Well, now that I'm all wound up, I might as well get it off my chest. Forgive me if I don't want to participate in the...

73 comments posted 20yrs

posted by rmd

73 comments posted 20yrs posted by rmd

Any one know what happened to Bean Products? servo controllers

A few years back I purchased a small servo controller that connects to the serial port of a PC. It came with some basic...

1 comments posted 20yrs

posted by dean.burell

1 comments posted 20yrs posted by dean.burell

Transmitter and Receiver

Where can I find a transmitter and receiver combo that will reach 2000 ft. for controlling the board of a wheeled robot?...

6 comments posted 20yrs

posted by williamso5

6 comments posted 20yrs posted by williamso5

Mitsubishi Movemaster RM-101 Manuals or software sources

I'm new to robotics and just got a Mitsubishi Movemaster RM-101 Robotoc Arm from about 1984 and the only documentation...

0 comments posted 20yrs

posted by trottier

0 comments posted 20yrs posted by trottier

5V DC Motor

Hi all I am looking for a gear motor that would run at somewhere between 150 and 250 rpms at 5 volts DC. I can't find on...

1 comments posted 20yrs

posted by kitmor

1 comments posted 20yrs posted by kitmor

Vacuum cleaner blocked pipe and/or robbag full sensor

Some domestic vacuum cleaners on the market use a simple spring loaded mechanical gadget to indicate the blocked pipe a...

6 comments posted 20yrs

posted by mh

6 comments posted 20yrs posted by mh

Discharge profile of a SLA battery/5V LDO

I'm starting to work on designing a power supply system for my rover. I've chosen to provide two batteries, one for log...

1 comments posted 20yrs

posted by mehaase

1 comments posted 20yrs posted by mehaase

Electronic control of air flow

Hello, I am interested in using air to launch a projectile from a remote contolled helicopter. I am thinking of using a...

7 comments posted 20yrs

posted by Todd.J.Olson

7 comments posted 20yrs posted by Todd.J.Olson

Looking for micro-potentiometer

Hi. Has anyone worked with micro-potentiometer with size in the vinicinity of 2~3mm in diameter? (Hopely with a good li...

2 comments posted 20yrs

posted by napdo

2 comments posted 20yrs posted by napdo

Collision avoidance

Hi, I know this is a boring question but I made some search without find good answer : can anybody link me a paper abou...

2 comments posted 20yrs

posted by richi.rasega

2 comments posted 20yrs posted by richi.rasega

ideas for pressure sensing device?

Hi there, strictly speaking this isn't directly about robotics but I know that robotics people are the ones most likely...

11 comments posted 20yrs

posted by spam.ontoast

11 comments posted 20yrs posted by spam.ontoast