Finally finished my first layered depth map - took way longer than expected

Nov 19, 2026 Last reply: 1 hour ago 5 Replies
Jump to replies (5)

Spent the better part of two weekends making a layered wooden map of the lake my parents live on, and I learned a ton. I figured the contour lines woud be the easy part. Wrong. Getting clean closed shapes from the depth data took most of Saturday, and I redid three layers because they had little gaps that would've dropped out of the frame.



The stacking was the fun bit. I cut each depth level from a diffrent blue-toned ply, dry-fit them, and glued them up on a flat board with a weight on top. Roads and town names got engraved on the top layer, plus a small compass rose in the corner. Water on, it reads like actual water, which still makes me grin.



Biggest tip for anyone trying this: build in some margin around your water so the outermost contour has land to sit on, and test-cut one layer before committing a whole sheet. My first attempt had the deepest layer riding right on the frame edge and it looked off.


I've made a few of these stacked water maps over the last couple years, mostly of the harbor town where my wife grew up, and the contour cleanup stage is where I lost the most time too. What finally worked for me was simplifying the polygons before I even thought about cutting. Each closed shape loses a little width wherever the outline doubles back on itself, and if a ring is too thin anywhere it becomes a paper-thin sliver that snaps or drops out. I now check every level by eye at high zoom and fatten or delete anything that looks fragile. On materials, I stopped using different colored ply and went the other way with plain 3mm birch, then tinted the water layers myself with dilute paint. Cheaper sheets, and if I wreck one layer I'm only out a few bucks instead of a half sheet of the fancy stuff.

One thing that saved my sanity on assembly: don't glue all layers at once. I did my first piece that way and the whole stack shifted a hair while clamping. Now I do two or three layers at a time with yellow glue and a brayer to roll out air pockets, then let each stage set fully before adding more. For the engraving, keep your text well inside the top layer outline. Mine sits maybe a quarter inch from the waterline and the burn halo makes it look cramped. A little breathing room reads much cleaner.

I built one of these for my in-laws' cabin on a reservoir we visit every fall, and I skipped the colored plywood entirely. I cut every layer from the same 3mm birch and stained the water rings with wood dye, one shade darker per level, then hit them with spray lacquer. Cost me a fraction of what the tinted stock runs, and the tones came out richer than any sheet I could have bought. Downside is staining thin rings is fiddly and I dripped on two layers before I started masking the land side with tape. For the shape cleanup I took a totally low-tech path compared to the polygon advice above. I bought an old paper fishing chart of the reservoir, scanned it, and traced the contour rings by hand in Inkscape over the scan. Took an evening but every ring closed on the first try because I drew them as clean loops instead of processing raw data. Crude, maybe, but it worked for a decorative piece where nobody is checking depth accuracy. One thing I did differently on assembly: no backer board. I drilled hidden dowel holes through each layer and ran short dowels with spacers, so the levels float a few millimeters apart on the wall. The shadow gaps between rings read almost like water is moving. Not for everyone, needs a solid hanging spot on the studs, but it changed the whole look versus a flat stack.

This takes me back. Before I had proper software I did a piece like this by tracing bathymetric charts onto mylar at a light table, then taping the sheets down and cutting by hand with a scroll saw. Three weekends of squinting and a saw blade per layer. Two weekends sounds like a vacation to me. Curious how you handled the clock bit, did you sink the movement into the back board and let a ring of water act as the face, or mount the whole stack proud of it? My first clock map had the hands dragging on the second layer and I had to space the whole assembly out.

The staged gluing advice matches what I landed on too after a bad first attempt. I also drill two tiny registration holes through a corner of every layer before any glue touches wood, then slip toothpicks through the whole stack while it sets. Takes five extra minutes and the shoreline stays lined up no matter how the layers creep. Even helped when I had to swap out one middle ring that came out with a scorch mark, new piece dropped right into place.

Update: tried the registration holes trick with toothpicks and my last stack stayed dead on, wish I'd known that the first time. Still fighting the contour cleanup though, my depth data keeps making wierd little spikes where the survey points are sparse. Does anyone know a good way to smooth that out without losing the real shape of the shoreline?

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required