1. Home
  2. 🔒 Lockmithing and Lockpicking Discussions
  3. MSRP for Ilco 7108???

MSRP for Ilco 7108???

Loading thread data ...
formatting link
Froogle is your friend. Retail $137. I put in a couple for a guy awhile back. And then he wanted a couple more. IIRC, they were about $125 for the lock, and then some labor to put em in. A couple years ago.
Reply to
Stormin Mormon
When installing, t here is a template. Please note that on some models (I think this one) the hole locations are different if LH or RH door. Because the slot in the bolt is not centered, the lock can be up or down a bit.
2 1/8 cross bore works fine.
Reply to
Stormin Mormon
This is a new install. I believe the bore is 1-5/8. This is a solid wood door that is 2" thick-with a 4 inch stile. I could not find 7100 with 2" BS. I could fit a LORI 2"bolt-but warranty would be voided. Know about the arrow-think thats why the instructions read: place template on the outside. Should'nt be much trouble. Thanks Stormin'
goma.
Reply to
goma865
The couple I've done, they work very nicely with a 2 1/8 cross bore, so you can use the Kwikset drill jig. The narrow wood frame might be a probelm.
1 5/8 is what Schlage uses for, hang on. I'm thinking Dexter. Well, Dexter used to use 1 5/8. Schlage was 1 1/2. For the deadbolts. The knobs (Schlage and Dexter) use 2 1/8 cross bore.
Reply to
Stormin Mormon
The 1-5/8 is what I went with. Most of the time I go with smallest bore I can-unless it already exists.. (Lori's-I use 1-7/8) It will fit over an existing 2-1/8. Less material removed from the door stile. This was an 8 foot door-solid wood-beautiful. Got it done.It looked great. Customer happy. Changed combo and all. Had to go easy with spade bit on the 1 inch bolt bore. But touch and go and I got it.
Later, goma.
Reply to
goma865

Site Timeline

Related

  • Bright Flares

  • Aluminum welding is coming along , just need lots of practice now . But SS is...

  • brass or gold finish look

  • how do you get the brass or gold finish look, i've seen many pieces thatlook...

  • Oil Rubbed Bronze Finish

  • The piece is actually brass, with a bronze finish ("distressed Venetian bronze",...

  • 2 "ground rod" questions (Thumper aka cable fault locator)

  • I have these hand planes I make and I need a better finish on thebrass. I have...

  • JUST WONDERING.....

  • I was wondering if there is anyone out there that has seen a picture of the...

  • ILCO Typo

  • I am getting to where I dont think MUCH of Ilco AT ALL any more.. too many...

  • Ilco Universal II

  • Hello, Has anyone used the Ilco Universal II code cutting machine ? And if so...

  • ILCO - X1011KR

  • I just received them via special order from Ilco through McDonald-Dash. I paid...

  • Wondering where

  • Anyone know where the shuttle Enterprise is at present? I got to see it...

  • Ilco unican 1000

  • My ilco unican 1000 pushbutton lock recently stopped working. Everything seems...

  • Machining Alloy 260 Brass

  • Hello group,I was wondering how easy Alloy 260 Brass is to machine?My project is...

  • Tig welding brass

  • You can TIG Braze-weld it using silicon bronze or sil-phos-bronzefiller, but...

  • If you guys were wondering how my date went

  • You have found the secret - be who you really are! If there is not any sparks,...

  • Brazing brass cymbals

  • I have been asked to repair a couple of brass cymbals from a drumset. They...

  • Threading brass rod

  • I have no doubt that I am either being impenetrably stupid, or justconfused ,...

  • "Bright Boy" not a "bright" idea?!

  • I know this subject was touched on a little while ago; but I'm horrible at...

  • Bright LED

  • I'm playing with a Luxeon K2 LED that I finally was able to glom as anobody....

  • Good finish when milling an end of a brass piece

  • Someone at works wants me to mill a end of a rectangular brass bar,about 3/16x1...

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.