Interesting machine

Still being coy?? Sheeit, we ARE your 24/7 bidniss/tech consultants, so you SHOULD divulge details.....

But the parts value could be considerable. Old motors, tho, were not renowned for efficiency. New Baldors (and others) are topping 98% (claimed) effic -- ackshooly, for quite some time now..

Everybody uses short tons... easy conversion, I spose. 2,000#, right?

I'da thought more, but still in the ballpark. I don't scrap, just bring my own s*it to the yard in m'pickup, and DATS time-consuming. Dead LEAVES are time-consuming.... lol

I paid 6k.

Scrap yards pay me 290 per short ton, and with this much I hope that I can get 300/ton.

There is steel, copper wire, electrical controls, valves, hydraulic power units, and motors, among the sellable parts.

This is not how I estimate, I go by known machines (like "cincinnati vertical mill 14k lbs) and think, how many of those would be about equivalent to this machine.

I am not great at estimating yet. But I have to learn. I keep spreadsheets of how much I make from scrap machines.

I used to do the same thing.

You should do alright.... proly not a windfall, but still worthwhile. Depending on how you handle "parts", tho, you might have some of those for a while. Thank gawd for ebay....

If I had the money, space, I'd put alladis in a "manufacturing museum". Lord knows, Merka already needs one.....

It is not really that good for a museum, it is not like steam punk or some such. There is nothing remarkable about this, except the size.

But in one way or another , we all milk RCM for personal gain. If we did not get something from RCM , why would we log on.

Dan

Entertainment, silly goose...

Got yourself a nice plasma cutter yet? Might be a good job for one.

Gunner

The methodology of the left has always been:

1. Lie
2. Repeat the lie as many times as possible
3. Have as many people repeat the lie as often as possible
4. Eventually, the uninformed believe the lie
5. The lie will then be made into some form oflaw
6. Then everyone must conform to the lie

This is heavier stuff, cutting bolts etc. Plus it will be at the job site, not at my place.

Plasma cutters can not cut very thick metal. Most plasma cutters are limited to an inch or less , but do work on stainless.

Dan

It would not be practical to use a plasma cutter for scrapping machines. Many reasons, such as them not being as portable, needing compressed air, electricity etc, cut thickness and so on.

The American Precision Museum, which is full of old machine tools, wouldn't touch something like that.

They wouldn't even take my little 1917 Taylor & Fenn knee mill. I tried. d8-)

How about one of those oxygen lance things?

Best regards, Spehro Pefhany

Who's our resident plasma cutting expert?

Questions: How critical is it to have super dry air? Will running it from a freshly drained compressor tank hurt it? Would inline filter driers work, such as are used at the ends of spray painting air lines?

Yes and?

Gunner

The methodology of the left has always been:

1. Lie
2. Repeat the lie as many times as possible
3. Have as many people repeat the lie as often as possible
4. Eventually, the uninformed believe the lie
5. The lie will then be made into some form oflaw
6. Then everyone must conform to the lie

"Most"?

Many can do up to 1.5" in Burn/Gouge mode.

Thats in Single Pass. You can burn that same amount in the second pass..and in the third....

My Miller 2050 is rated at 3/4"

Ive cut 2" steel with it.

Gunner

The methodology of the left has always been:

1. Lie
2. Repeat the lie as many times as possible
3. Have as many people repeat the lie as often as possible
4. Eventually, the uninformed believe the lie
5. The lie will then be made into some form oflaw
6. Then everyone must conform to the lie

But in one way or another , we all milk RCM for personal gain. =================================================

There are soldiers, and mercenaries. There are swinging doors, and ratchet-and-pawl turnstiles.... There's milking, and chewing off the nipple. Etc.

Ultimately, you are correct in some sense -- most here ARE getting something out of this relatively one-way exchange. But it reminds me of the super-great Yellow Pages ads, years back: You had to guess the subject from the skit, in this case: Oh, enough of me, let's talk about YOU, now, dear: What do YOU think about my latest movie????

Subject: Vanity Cases.....

Look, ig, I'm sure, is a tax-paying patriot, who loves his kids. I'm just sayin we should all get a tip, at Xmas.....

You did note that plasma cutter requires three phase power, oxygen , and Argon. Not exactly what I would call a portable machine.

Dan

In my opinion, the saga of Bridgeport Interact CNC conversion was such a tip, lots of useful information was posted.

Yeah, ig, simply KNOWING you is an honor and a privilege.