1. Home
  2. ⏣ General Metalworking
  3. Need fabricator to build 5' Dia 1 to 2 inch steel circles

Need fabricator to build 5' Dia 1 to 2 inch steel circles

My project is to build one or two round bale horse feeders. These hay feeders
will be loaded with rolls of hay 5 feet in Dia and 4 feet tall. I have not been
able to locate the 5' rings so far and thought they might need to be fabricated
locally. Can anyone give me some insight where I might start my search.
Reply to
john reed
Loading thread data ...
My project is to build one or two round bale horse feeders. These hay feeders will be loaded with rolls of hay 5 feet in Dia and 4 feet tall. I have not been able to locate the 5' rings so far and thought they might need to be fabricated locally. Can anyone give me some insight where I might start my search.
Reply to
john reed
My project is to build one or two round bale horse feeders. These hay feeders will be loaded with rolls of hay 5 feet in Dia and 4 feet tall. I have not been able to locate the 5' rings so far and thought they might need to be fabricated locally. Can anyone give me some insight where I might start my search.
------------------- Google: "metal fabrication near me" "diy round bale feeder for horses"
Reply to
Jim Wilkins
Or he could visit the local farm supply store . ----------------
Like the X-Files genie I give people what they ask for.
formatting link

Reply to
Jim Wilkins

Site Timeline

Related

  • bending 5 foot dia circles of 1/2 or 3/4 EMT pipe

  • Hi Larry,Tubing bender is just two expensive for fabrication just a few (as...

  • MT 5-1/2 ???

  • Overall I am pretty happy with my Chinese made Precision mathews PM1440LBE ...

  • Where can I buy a 1/2 inch dia dead centre

  • I have acquired a small (= cheap) boring head which accepts 1/2 inchdia boring...

  • 1 3/4 inch step drill bit ?

  • I need to drill a 1 3/4 inch hole in ABS plastic. I presently have great luck...

  • Need a source for 1/2" and 5/8" steel balls

  • I need to get some 1/2" and 5/8" steel balls. They don't have to besuper...

  • Concentric bolt circles?

  • I need to make a couple of adapter plates for the new 56HP Yanmar to fit the...

  • Alternatives to LPS-2

  • I found another penetrating lubricant called PB-50 (by the samecompany that...

  • Need oddball bolt: 1/2" x 12 TPI

  • Actually, according to the Wikipedia article on Whitworth, it was used in the US...

  • 1/2" dia carbon fibre round

  • Looking for a source for a small quantity of 1/2" dia carbon fibre orgraphite...

  • Soldering to steel (fuel tank)

  • I am trying to solder a brass fitting to the fuel tank. By the way, the tank did...

  • welding stainless steel to platinum

  • I have a problem figuring out how to weld platinum to stainless steel. What...

  • best way to get 1/2" holes through 1/2" Stainless Steel Plate?

  • Hello,I had this issue last year and with the help of someone from...

  • Butt Splicing Aluminum to Steel 1/2" Flex.

  • I need to extend a steel conduit run. Is there anything wrong with buttsplicing...

  • Bending 4mm dia stainless steel rod

  • Hello, can anybody tell me how much I can bend a 4mm dia 316 ss (or304ss) rod in...

  • 1 inch impact and 1/2 inch compressed air piping

  • In a certain surplus deal, I acquired four trailer+pickup truck/loadsof various...

  • How to tell high speed steel from carbon steel

  • I have a few "Ace" taps made by Hanson. (large sizes, 5/8 to 7/8NC). They do not...

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.