⏣ General Metalworking

30778 Threads Posts
to

16 foot step ladder?

This is off subject here but where can i purchase a 16 foot step ladder? Bill
4 comments posted 21yrs
posted by bill
4 comments posted 21yrs posted by bill

diamond grinding wheels again?

I am bringing up a Baldor "carbide" tool grinder, a No. 500 with tilting tables that takes plate-type wheels. I have no...
26 comments posted 21yrs
posted by grant
26 comments posted 21yrs posted by grant

NAMES Expo (Updated 24 Jan 2005)

A reminder. The 16th Annual North American Model Engineering Society (NAMES) Exposition When April 23-24, 2005 Hours Sa...
0 comments posted 21yrs
posted by ssl
0 comments posted 21yrs posted by ssl

Using VFD with RPC

I have a 7.5 horse RPC and use it to run my Sheldon VS Lathe. The lathe motor is 2HP 3 phase. I was looking at VFD's an...
10 comments posted 21yrs
posted by Sierevello
10 comments posted 21yrs posted by Sierevello

Foundry Updates 12 & 13 - Posted

Foundry Updates 12 & 13 - Posted http://www.theworkshop.ca/casting/Foundry/fndry12/Fndry12.htm http://www.theworkshop.c...
3 comments posted 21yrs
posted by frnkgmbk
3 comments posted 21yrs posted by frnkgmbk

Wal-mart welders

Hey guys, Since i was a little kid i been fascinated by the art of welding. I been thinking of learning how to weld. To...
19 comments posted 21yrs
posted by myc1972
19 comments posted 21yrs posted by myc1972

Repost (again) Photos in dropbox

Sorry if this shows up twice (or three). I suspect my isp's news server ate it (pretty sure it's receiving but ain't se...
3 comments posted 21yrs
posted by keillorp135
3 comments posted 21yrs posted by keillorp135

Mill/Drill Anti-backlash nut source?

Hi, I have a mill/drill with about 0.030" and 0.045" of backlash in x and y directions. It would be nice to get this do...
8 comments posted 21yrs
posted by petermichaux
8 comments posted 21yrs posted by petermichaux

VFD Placement

Hi, I want to mount a VFD over the headstock of my lathe, on the wall. This VFD comes with 1/2 knockouts so I can cable...
7 comments posted 21yrs
posted by wayne1NOSPAM
7 comments posted 21yrs posted by wayne1NOSPAM

b&s #9 taper converted to R8

Greetings all, Last summer I bought a nice little horizontal mill. The spindle taper was a Brown & Sharpe #9. Looking u...
1 comments posted 21yrs
posted by etpm
1 comments posted 21yrs posted by etpm

Covering up the solder in a copper project

I am working on soldering copper joint for this project: http://home.earthlink.net/~madur0/copperhood.jpg I was told th...
6 comments posted 21yrs
posted by dryer
6 comments posted 21yrs posted by dryer

Steel Flanged Bearing Sleeve

I'm trying to repair an office desk chair where two of the parallel pivot points on the chair base assembly have gotten...
6 comments posted 21yrs
posted by MGDW84B
6 comments posted 21yrs posted by MGDW84B

Phase Converters

Hi guys, I have been online Googling pahse converters. Will a static phase converter be adequate for a 1 HP Bridgeport...
21 comments posted 21yrs
posted by jbacc
21 comments posted 21yrs posted by jbacc