⏣ General Metalworking

30778 Threads Posts
to

THE MACHINIST (a movie)

I was just curious. I suspect that the readers here aren't the regular art house, movie-going crowd here, but I'm wonde...
11 comments posted 21yrs
posted by SP-AMB-LOCKrainlover
11 comments posted 21yrs posted by SP-AMB-LOCKrainlover

Good bench grinder?

I'm in the market for a bench grinder and am looking for some feedback on good choices. I am pretty certain I want an 8...
7 comments posted 21yrs
posted by benh
7 comments posted 21yrs posted by benh

Another tool ID needed XXVI

Just posted a few more photos, and some answers to the last set: http://puzzlephotos.blogspot.com/ Rob
14 comments posted 21yrs
posted by rhvp65
14 comments posted 21yrs posted by rhvp65

source for large washers?

rec.crafts.metalworking source for large washers? Anyone know who sells 2.5 inch steel washers .125 - .188 inches thick...
5 comments posted 21yrs
posted by htytus
5 comments posted 21yrs posted by htytus

Any HSM use for "wearing compound"?

I have a quart or so of "wearing compound" that I found at the dump. It's a 2-part epoxy (?) with small (.06 +-) cerami...
0 comments posted 21yrs
posted by bobengelhardt
0 comments posted 21yrs posted by bobengelhardt

cnc router tables

Take a look at the products on offer from Axyz Automation. Good range of products for most industries. www.axyz.co.uk A...
0 comments posted 21yrs
posted by pking
0 comments posted 21yrs posted by pking

"THE BEAST" is alive

Most all of my posts over the last year have been toward working on the new shop and my old CNC machines installed ther...
1 comments posted 21yrs
posted by karltownsend.NOT
1 comments posted 21yrs posted by karltownsend.NOT

Metal Casting Question

Hello, Does anyone have any idea where I can get about 50 small specialty bolts (about an inch and a half long) cast in...
6 comments posted 21yrs
posted by jim
6 comments posted 21yrs posted by jim

Anti-slip bit for slotted headed screws

< http://www.metalworking.com/DropBox/Power_screw.pdf > describes making a bit for driving slotted head screws. Until I...
8 comments posted 21yrs
posted by Ted_Espamless
8 comments posted 21yrs posted by Ted_Espamless

OT: A Truly Political Moment in America

Greetings and Salutations.... Ok...I KNOW it does not have anything to do with metalworking, but, this was just too gre...
1 comments posted 21yrs
posted by xmundt
1 comments posted 21yrs posted by xmundt

Compressor unloader?

Hi all. I've got an air compressor that won't shut off when it reaches it's maximum pressure. Am I correct that there i...
5 comments posted 21yrs
posted by aol.nospam
5 comments posted 21yrs posted by aol.nospam

2 prong vrs 3 prong electirc plug

Ya gotta help me out here. We have a running battle in another forum concerning devices that are submerged in ponds / a...
5 comments posted 21yrs
posted by chipmkr
5 comments posted 21yrs posted by chipmkr

Drilling Speed and pilot drill questions

I was going through my Machinery Handbook, and trying to figure out the optimum drilling RPM. I ended up having to look...
28 comments posted 21yrs
posted by fergusonOMITsculpture
28 comments posted 21yrs posted by fergusonOMITsculpture

Unions are killing this country!

Unions are killing this country, here's a prime example. I don't know about other areas of the country, but a growing t...
19 comments posted 21yrs
posted by jwisnia
19 comments posted 21yrs posted by jwisnia

Tornio Anselmi MonoFAP 180 AE lathe

I have a problem, i byed a used lathe from a local machinists scool. The operating/maintenance manual is missing. Does...
0 comments posted 21yrs
posted by nkrbjhvee
0 comments posted 21yrs posted by nkrbjhvee