Power Factor and New Power Company Digi Meters

Initially I had a bill for =A329 only

Thought that's wrong...............and knowing how they work ...ie you will be billed higher at a later date I phoned them up.

They then asked what reading I had on my meter now ...and then came back with the new calculations ....=A3300

and according to them ....this is from a an official meter reading...to my reading ... and I've used something like 2500 units .

They told me this is out of line with what I have normally used in the past ...and even they think there is something wrong with the meter .

And I wasn't talking to a Muppet ...I had the manager of this section of British gas phone me back.

Like i said there is something wrong ... I used 11 units yesterday in the space of two hours ....that's just with my comp on and my converter and the lathe.

that's with me using the electricity like I do normally ...ie no cooking ...bought a take away ....no tumble dryer etc ...

all the best.....mark

That definitely sounds dodgy - 5.5 KW sounds a tad over the top for a PC and a lathe.

Your next door neighbour hasn't tapped into your supply by any chance...?

Regards, Tony

I'm not happy

I phoned up Ampy the maker of this meter.

and they say it DOES NOT TAKE INTO ACCOUNT POWER FACTOR it reads only in kva hours.

MODEL NUMBER

British gas say they will not change the meter.

BRITISH GAS SAY THAT EVERYONE WILL HAVE ONE OF THESE METERS INSTALLED WITHIN THE NEXT FEW YEARS

They also say that "ALL" other electricity providers are going down the same route

so therefor you're all going to be in the same boat as me .

ie your overall electricity bills will shoot up 75 percent if you use your machinery in your workshop for a couple of hours a day...domestic

Example I used to use about three units on the old ANOLOGUE meter for ...for a couple of hours work in the workshop

This new fangled digital meter now reads 11 units of the same time period .. the new meter isnt faulty ...this guys is the future

I URGE EVERYONE HERE ...WHO HAS ONE OF THESE DIGITAL METERS FITTED TO GET IN TOUCH WITH

ENERGYWATCH

They wont have a clue what you are talking about ...but the more people phone this number ...the more this fraud will sink in with them.

All the best.......mark

INSTALLED

day...domestic

Perhaps I'm missing something here, but haven't we ALWAYS been charged for KVA as domestic customers ? The 'old fashioned' spinning wheel type meters read KVA as I understand it

AWEM

I've just checked, my ABB 'digital spinning wheel' meter, about 2 years old, *says* it reads kWh. I couldn't comment on the theory of which it measures, though Having said that, my bills did seem to go up substantially after it was fitted, but I used to be pleasantly surprised at how low they were with the old meter. Perhaps the old one was faulty ! Presume the meter Mark is talking about works on a different principle

- does it just measure volts & amps and combine them? If so the meters are probably cheaper to make, no moving parts, that could be one reason for the change.

Tim

Dutton Dry-Dock Traditional & Modern canal craft repairs Vintage diesel engine service

You're missing nothing Andrew. The only way the new meters will read more than the old ones is either when they are faulty (unlikely) or the previous induction disc meter was under reading which is much more likely.

As the whole metering systems throughout the electricity industry, right from 23kv at 30,000 Amps on the generator, to 400kV at 3000 Amps on the transmission system, through bulk supply points at 11kV and

The figures generated, match the figures supplied less known losses. They are extremely accurate and regularly checked with two different manufacturers meters for instance at every critical point, any discrepancies have to be accounted for. The technology in them is very similar to those in the new domestic meters.

But, induction disc metering is also very accurate and they certainly don't under read by 3/11 of the usage as mentioned unless there is a serious fault. If the error came to much more than 0.5% I'd be very surprised - the statutory limit is, if I recall correctly 1.5%.

Not measuring reactive power is a very good thing for anyone running machinery. Given the choice the whole of manufacturing industry together with major commercial premises would prefer KVA only metering just like the domestic customers fortunately have. So, your meter might possibly be faulty Mark, but make the right noises and you can get it checked or replaced. It will cost you for the investigation, but if you are correct you will get all the costs back plus the cost of the overcharged electricity. Or, do it yourself and buy an induction disc meter off of ebay and wire it inline with your workshop load. Maybe buy an electronic one too and see what they read - They can be had for about a tenner a piece plus postage.

Technically KVA can be reactive power and that's usually how it's used; KWh is not reactive but a real power measurement (OK energy measurement). If the energy company charges you for energy used they must use a KWh meter, if they're charging you for amps then the KVA meter is what they should use. Industry has long been charged for KVA R whereas, until recently it seems, domestic single phase users have been charged for KWh. If you get 3 phase installed at home, you get charged industrial rates. There is a general push to get all equipment that goes through CE approval to achieve a power factor of >0.9 to reduce current (and heating losses) in the power distribution system but motors etc. won't achieve this without the use of power factor correction (PFC) networks. Martin

I strongly suspect that someone is talking bollocks here. All domestic metering will tend to go electronic in the next few years (about time too). AFAICT no utility in the UK bills based solely or even partly on VA consumption to domestic consumers. Even the Energy watch site talks exclusively about kWhr.

Contracts for kWhr with an availability charge for peak kVA on a period rate are standard in industry and might be instituted by default if one has a three phase supply or if the previous bill payer had a business contract. But note that the availability charge is a fixed per day/month/quarter uplift based on peak usage.

What does your bill say? If it really said you were being charged for X many kVAhr, then simply change to another supplier, as is your right and can be done in a matter of hours. If it says that you are being charged per kWhr and you feel that the meter reading reflects kVA then demand a meter test, but be prepared to pay if the meter is accurate.

Keep us all informed as to your luck on this one...

regards Mark Rand RTFM

My mistake, the kVA slipped in there. I meant kWh ! All domestic meters measure kWh regardless of how they are implemented. They don't give a stuff about power factor so you can put as many motors on the supply as you like and will blow the supply fuse well before the meter starts reading anything other than kWh.

This is quite frankly a storm in teacup. If there was even the slightest hint of a problem, a great many users would have been aware of it well before now.

Sorry for these caps

A HUGE MOTOR WILL USE LOTS MORE UNITS THAN A CELLPHONE CHARGER PLUS ELECTRICITY HAS DOUBLED IN PRICE DURING THE LAST YEAR!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

I can only quote facts

11 units after

if you look back a few years back when I asked about power factor, you will see when i had the fright of my life when a friend put a clip on ammeter onto one of the tailings .

it was showing that my 3 hp compressor was using 40 amps start up and

you guys here explained power factor to me then

and basically told me to watch what the actual meter counts .. so i did an experiment with the compressor chugging away ...with the receiver valve partly open so it didn't cut out

I did this over half an hour

and was pleasantly surprised that it wasn't using anything like 26 amps... which is ... 6 240 watts or 6.2 units an hour and the analogue meter showed it to be using something like 2500 watts or 2.5 units per hour

SO ON FROM THERE ...i believe this new digital meter is reading the same way that that clip on ammeter was reading.

so you guys are now disputing me and trying to reverse everything

do you guys work for British gas or something.

or do you trust in everything this country does to you, and tells you. .............and see no evil etc.

all the best.....mark

Read what I said....

Mark Rand RTFM

Odd then that the only reference to it on Google lists it as an energy meter, that means kW hours...

You've admitted that you don't understand this field so I suspect that you're simply getting confused when talking to these people. A digital power meter does not "correct" for power factor, it measures true power regardless of power factor. If the meter is to display power factor it has to calculate it as a secondary or derived value.

If you doubt what I'm saying please go to this site:

Does you bill still refer to kW hours?, if so they can't possibly be metering kVA hours as this would be fraud, pure and simple, there is no way they can know the kW hours you've used from metering the kVA hours, they can only know the maximum you could have used IF your load were purely resistive, and no one is.

Whatever the situation you have, you can fit pf correction capacitors to your machinery to bring the pf back near to unity, not a bad idea as the world burns a hell of a lot of fossil fuels just to heat up the generation and distribution systems because of bad pf. This is why the generators are planning to meter kVAr domestically as they have been doing industrially for many years, but I've not heard any suggestion they intend to install kVA hour meters as the way to do it, instead they intend to install meters that measure both kW hours and KVAr hours.

Greg

You're sounding more and more like a troll, did you just ask them to change the meter because you thought it faulty as I suggested or did you try and be all clever with them, arguing technicalities you don't understand, I wonder.

Greg

One simple question and maybe you could give a straight answer, what does it say on your meter?, mine states kWh above the display and 1000imp/kWh above the flashing LED. If yours says the same or similar then that's what it's measuring, power, no maker would ever get a meter approved if it said this and actually measured kVAh. Greg

Any suggestions on how to size PF capacitors? It's certainly something I have never even thought about.

We have just had southern electricity tell us they will raise our direct debit to 200 a month!! Seems we been paying too low an amount for a fair while. Now I'm closely monitoring the meter.

Might pay to get three phase installed if I'm actually using that much more than average!

Wayne...

Yup anyone on these news groups ...that seems to be loosing an argument gets called a troll ...that's how they work ...so it seems

And I've also noticed how people get ganged up on as soon as someone seems to get something wrong ... other people jump in and say the persons wrong ..........just for the hell of it .

and if that becomes more likly here ..i will simply not answer any more questions on the subject ...or read it.

nope did not argue tech with them

just said that 1-3 units used before 1.5 to 2 hour period

and 11 units used after meter install over same period .

I just said "is this something to do with this power factor malarky...and thats it "

they guy from British gas said he understould power factor .

and he thought himself that something was amiss with the way these meters read the power.

(AS his father had a small machine shop at home ...and had been grumbling)

he said, he did all he could to convince his superiors that i had a case .. he said there wasn't any budging in them .

I have an old analogue meter (faranti same as the old one) ...i know it was bought from a car boot sale ...but its all i have to check this out myself ...so cant vouch for the blooming thing

shall be putting it on at the weekend ...to see what's going on myself.

YOU say you designed them Greg ...then I wouldn't expect you to knock them.

All the best...mark

Yes it says ...what yours says .

does that mean i have a faulty one .

all the best..mark

It was you who started getting personal:

"so you guys are now disputing me and trying to reverse everything do you guys work for British gas or something. or do you trust in everything this country does to you, and tells you. .............and see no evil etc."

so don't play the innocent.

Is that your excuse for not answering my very simple question about the marking on your meter which may clear all this up?

So I'm hiding something sinister am I, hmm, just a hint of paranoia there maybe?

Greg