⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Workshop calculator

Does anyone have a manual for a Sharp EL-9400 calculator, or could do a copy please? I have been given one for use in t...
4 comments posted 21yrs
posted by mffq25
4 comments posted 21yrs posted by mffq25

LOX generator....

Hi all, There was a thread here a week or so back (that I can no longer find) about building a liquid oxygen generator...
2 comments posted 21yrs
posted by dmills
2 comments posted 21yrs posted by dmills

Stuart No 1 Steam Engine.

Hello folks, just found this brilliant web site for anyone building o proposing to build the STUART AND TURNER NO 1 ste...
3 comments posted 21yrs
posted by redstar.1fok0a
3 comments posted 21yrs posted by redstar.1fok0a

Anyone got a LARGE bridge rectifer ?

>I'm looking for a BEEFY bridge rectifier to give me DC capabilities on my >Oxford stick welder - peak current 500Amps...
1 comments posted 21yrs
posted by diesel
1 comments posted 21yrs posted by diesel

Beginner needs help with gaskets

I'm building a 5" gauge 0-4-0 loco, 'Dougal' which has a port block the full width between the frames. What sort of gas...
1 comments posted 21yrs
posted by hattermadmark
1 comments posted 21yrs posted by hattermadmark

Myford gearbox

Hi all, I have a Myford ML7 with a standard gearbox (where you have to take the cover off etc.) I am having to recondit...
4 comments posted 21yrs
posted by dave
4 comments posted 21yrs posted by dave

Linear bearings

I'm kicking some ideas about in my head to construct a cutting table to take either an oxy-acetylene or plasma torch, a...
4 comments posted 21yrs
posted by andrew
4 comments posted 21yrs posted by andrew

Rubber

Hi Im looking to add some caterpillar tracks to my submarine. I need some long strips of rubber. Does anyone know of a...
22 comments posted 21yrs
posted by no
22 comments posted 21yrs posted by no

Slot Drills and End Mills Question

Going great guns with my new mill, but questions arise which are not in the book. Tubal Cain says to use slot drills ra...
14 comments posted 21yrs
posted by steve.withnell
14 comments posted 21yrs posted by steve.withnell

desperately seeking compressor for airbrush

Just wondered if anyone had come across a cheap compressor capable of 30PSI for home use with an airbrush (model painti...
14 comments posted 21yrs
posted by radish4mickey
14 comments posted 21yrs posted by radish4mickey

MEK&Acrylic

I think you were after a source for MEK, John, in-amongst other posts, any decent plumbers merchants sell it for cleanin...
0 comments posted 21yrs
posted by markgengine
0 comments posted 21yrs posted by markgengine

rivets in blind holes

I believe there was a previous post about the type and name of rivets that are hammered into blind holes but I cannot f...
7 comments posted 22yrs
posted by alan_marshallthomas
7 comments posted 22yrs posted by alan_marshallthomas

newbie question

Ok, I've got the 48 mm dia bored cast iron first stage cylinder, and the 22 mm dia drilled-and-reamed cast iron second...
12 comments posted 22yrs
posted by zenadsl6186
12 comments posted 22yrs posted by zenadsl6186

acrlyic crackling

okay - yet another question here - this time its about something I've done by accident before but this time I would lik...
17 comments posted 22yrs
posted by james
17 comments posted 22yrs posted by james

Ceramic immersion heating element

Okay - I'm looking for a small (200W to 300W) ceramic heating element to be used in a small andosing station mainly tho...
2 comments posted 22yrs
posted by james
2 comments posted 22yrs posted by james