brushless

Salve a tutti. Sono venuto in possesso di alcuni motori brushless a cassa rotante (dotati di sensori, a quanto pare) asportati da un macchinario industriale ed avrei cortesemente bisogno di un vostro parere a proposito della possibilità di reimpiegarli, alla stregua dei motori da cdrom, per scopi propulsivi.

Le caratteristiche principali sono: statore 12 poli d. 50 mm altezza 14,5 mm; avvolgimento a stella (non conosco il numero di spire); magnete in ferrite spessore 4 mm.

Nel caso fossero necessarie, ho fatto delle foto che invierò a chiunque voglia dare un occhiata.

Con grande riconoscenza, Fabio Caracciolo

Reply to
Fabio
Loading thread data ...

si possono modificare per bene..... magari intanto inizia a vedere questo sito:

formatting link
ciao

Reply to
il Zott (Roma)

Aspetta, aspetta... non è che sono stati tirati tirati giù da un "volatile" per essere montati su un altro ma più piccolo?????? :-)))))))))))))))))))))))

Ciao Fabio!!! Tutto bene? Stai ancora dalle parti di Novara? Se sì ti invito alla castagnata del Gruppo di Volo a Vela del Mottarone che si terrà in quel di Comignago (tra Borgomanero e Castelletto Ticino) questa domenica.

Volo elettrico, volo a motore, aerotraino, castagne e vinello buonissimo!!!!!!!

Se hai bisogno di info sai dove trovarmi!

Reply to
alevilla.it

Ciao, grazie a chi mi a risposto, anche in prv. Per il Zott, le informazioni del Ditto le ho "sucate" tutte, anche quelle in tedesco che non è proprio la mia seconda lingua ma che sono riuscito più o meno a tradurre. Davvero grande sito (ahimè! non c'è più un videoregistratore che resti sano dopo il mio passaggio...)!

Per Ale: per prima cosa perdonami, e lo dico col capo cosparso di cenere (di balsa, ovviamente) per non essermi fatto più vivo. L'invito per venire in aeroporto è ancora valido ma a causa di problemi... di alto comando dovremmo coordinarci con un pochino di anticipo, così posso spiegarti cosa è successo. I motori invece non sono di provenienza volatile, ma sono proprio motori amputati da un marchingegno che serviva a collaudare dei particolari idraulici. Grazie per l'invito a Comignago, ma non so se questo week end riesco a liberarmi. E sarebbe un peccato perchè il volo e le castagne sono la mia seconda ragione di vita. La prima non te la posso dire... CIAO!!

Reply to
Fabio

Ciao Fabio,

formatting link
is (partly) in English, Ralph is translating all the time:
formatting link

-> English

An Italian cd-rom homepage:

formatting link
Articolo Italiano sui Brushless da cd-rom:
formatting link
On this site, you'll find several links do Italian diy motor sites:
formatting link
An Italian cd-rom conversion discussion:

Do-it-yourself motor homepages, manuals, checks and tests in the first message of this motor builders tips and tricks thread. The checks and tests may save you from frying your controller. Thread is active, bookmark it for future refence and subscribe to it:

formatting link

Prettig weekend ;-) Ron van Sommeren

formatting link
int. E fly-in near Nijmegen, the Netherlands

Reply to
Ron van Sommeren

"Ron van Sommeren" ha scritto

Well done, Ron! As usually your messages are very useful.

For courtesy: time ago you posted a link with a table listing the winding diagrams for various teeth-magnetpole combinations. The link was:

formatting link
With this table there was also a table explaining the meaning of the various colours, but now I can' t find it. What colour is associated to good combination? What colour is associated to bad combinations? What colour is associated to non-working combinations?

Bye!

Reply to
Vyger

That's an old address. Go to

formatting link

-> English

-> winding table and scheme calculator

The colours are explained there, bottom of page.

Vriendelijke groeten ;-) Ron

formatting link
int. E fly-in near Nijmegen, the Netherlands

Reply to
Ron van Sommeren

"Ron van Sommeren" ha scritto

Thank you very much, Ron. Bye!

Reply to
Vyger

Goedendag,

The baronerosso links in my original message have changed, these are the correct ones:

formatting link
?showtopic=1087
formatting link
Prettig weekend ;-) Ron van Sommeren
formatting link
int. E fly-in near Nijmegen, the Netherlands

Reply to
Ron van Sommeren

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.