1. Home
  2. ✈ RC aircraft models
  3. Looking for old SuperTigre part

Looking for old SuperTigre part

The spray bar for the low speed needle valve on the carbs used on the
ST 60, (1970s version)
This Spraybar is a brass tube externally threaded on the outside for
the low speed needle valve, and threads into the carb rotating
barrell..
Any one have any old ST carbs they would part with?
Cheers!
Dave
Reply to
Dave
Loading thread data ...
I have sveral, not sure how old they are. I will take one apart and post a picture of it or send to your email if you'll give me an address.
Ted
Reply to
Ted
Hi Ted!
Sure... it is
mariners snipped-for-privacy@rogers.com
I also have an old ST 60 in need of a complete carb.
Willing to buy and pay shipping..
...........and send you a pix of part needed if that would help!
TY!
Dave
Reply to
Dave
OK, am busy building a twin right now but will try to get to it in the next few days.
Reply to
Ted

Site Timeline

Related

  • Lister D needle valve & non starter

  • Hi all, Just dug out the old D type from its winter retreat and thebugger wont...

  • Supertiger low end needle valve

  • Hi all, Has someone out there got a Supertiger .61 that they can check...

  • ASP 75 low speed needle setting

  • Does anyone have an ASP 75 that can tell me what the low speed mixtureneedle...

  • remote needle valve

  • I am looking for the part number for the remote needle valve that would work...

  • Zenoah G-38 High Speed Needle Valve Setting

  • I'm having a devil of a time setting the high speed needle valve on a...

  • How to extend the needle valve

  • I have a thunder Tiger Pro .25 engine that is in a coweled P47-thunderbolt. Can...

  • Looking for Low-Speed Alternator

  • I would like to buy a low-speed alternator (~60 rpm, 1 to 5 kW).I believe there...

  • need SuperTigre part lists

  • Hi,I'm looking for part lists of old SuperTigre engines.Especially for ST...

  • Extending a needle valve

  • I have a perry carb on my ST3000. I need to have an extended needle to...

  • Needle peening on welding

  • Can any one tell me , What is needle peening process ? As far as I knowit is a...

  • Does anyone know what thread size a tire valve stem and the Schrader valve are?

  • I went through that a while ago. The external threaded part of aSchrader valve...

  • Looking for needle Bearing

  • Can someonr tell me where I could find a Needle bearing?the bearing I am Looking...

  • [MERCATINO] Vendo supertigre G51

  • Vendo motore supertigre g51 ringr completo di silenziatore.Nuovo ancora da...

  • Spray mode

  • I was ordering gas today and asked about an 85/15 Argon CO2 mix to MIG weld in...

  • Linde Plasma Needle Arc Welder on Ebay

  • A identical one was discussed a month or so ago and various peopleemailed me...

  • run AC solenoid valve on DC?

  • I thought I would run these 125VAC coil 1.25" solenoid valves on DC toeliminate...

  • Remounting an OS .40 needle valve assembly

  • Hello, fellows.A couple of days ago I purchased an OS.40 engine, and then today...

  • How "remote" can a remote needle valve be?

  • The .61 engine I purchased has a remote needle valve, but the enginedoes not fit...

  • Need info on low speed rotational transducers

  • Dear friends;I am new to this newsgroup. I would appreciate your help on...

  • Excellent magneto & carbs info

  • Splendid Oz site well worth a good...

PolyTech Forum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.