⏣ Metalworking Craft

Need Help With This One.

Hello Everyone. I am a professional magician, and I am looking for the following: http://www.emeraldsocietyofillinois.o...

0 comments posted 22yrs

posted by magician

0 comments posted 22yrs posted by magician

Anyone out there want a project?

Hello Everyone. I am a professional magician, and I am looking for the following: http://www.emeraldsocietyofillinois.o...

0 comments posted 22yrs

posted by magician

0 comments posted 22yrs posted by magician

re metal

hi its very smooth very shiney and heavy it seems more bright than stainless i know this hasnt narrowed it down at all i...

4 comments posted 22yrs

posted by rooey

4 comments posted 22yrs posted by rooey

what metal

i have some round bar with the markings 60681/3S144D any help appreciated

1 comments posted 22yrs

posted by rooey

1 comments posted 22yrs posted by rooey

Copper Art Mural

Please check out: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3706160245 This is a great piece of art depicting...

0 comments posted 22yrs

posted by castles

0 comments posted 22yrs posted by castles

Left handed screw for drill chuck

I am sure this is a common problem some of you have already solved. Where to find a left hand screw to hold the chuck f...

0 comments posted 22yrs

posted by nospam

0 comments posted 22yrs posted by nospam

Need a Computer Plumber?

Best in the world. Techs featured in major publications. Satisfaction guaranteed. Free Trial to test drive them. Contac...

0 comments posted 22yrs

posted by coffe

0 comments posted 22yrs posted by coffe

Which is best "paint-on" etching resist?

Hi, I've been etching brass shim. I was wondering if anyone can suggest a good substance to use as a resist on the 'oth...

0 comments posted 22yrs

posted by kasterborus

0 comments posted 22yrs posted by kasterborus

Odd size Carbide endmill

Hi all, I'm looking for someplace that might stock odd size carbide endmills. I'm looking for a 4 flute carbide endmill...

1 comments posted 22yrs

posted by sheffield

1 comments posted 22yrs posted by sheffield

Question about etching tanks

Hi, I'm etching brass (0.005" thick) using a small tank I built at home. I heat the etchant (Ferric Chloride) to 82F us...

0 comments posted 22yrs

posted by kasterborus

0 comments posted 22yrs posted by kasterborus

Seized Raglan 5"

I've eliminated most of the causes relating to why the spindle is seizing. The sliding back-gear selector seems to be p...

4 comments posted 22yrs

posted by noentrance

4 comments posted 22yrs posted by noentrance

FS: Dayton Abrasives Inc. Cartridge Rolls CHEAP!

I have many hundreds 50 & 80 Grit Dayton Cartridge rolls . Great for sanding or shaping Metal or wood. Priced below whol...

0 comments posted 22yrs

posted by hargol

0 comments posted 22yrs posted by hargol

heat treating qustion

I am a woodworker and I have never really done any smithing or metal work. But I just purchased some 01 precision groun...

2 comments posted 22yrs

posted by speedbuggy

2 comments posted 22yrs posted by speedbuggy

Materials Source

Hey all...I was just wondering if anyone has any information that could lead me to a source for aluminum (around 100lbs...

0 comments posted 22yrs

posted by monkiespersonal

0 comments posted 22yrs posted by monkiespersonal

Ragan 5" siezed

At least, I think that's it's name! Anyway, when I am operating it in auto-traverse, it runs happily and then the spind...

0 comments posted 22yrs

posted by noentrance

0 comments posted 22yrs posted by noentrance