OT: Removing floor tiles

Jun 24, 2004 35 Replies
Jump to replies (35)

About 20 years ago my wife laid our living-dining room in floor tiles,



12" squares of linoleum glued down. Now we need to remove the tiles and it is becoming a major PITA. Some areas of the tiles come up pretty easy, but a lot of areas have to be chipped up at great labor. I'm using a shovel-like METAL tool designed for the purpose with a resharpenable blade about 7" wide and in the tough areas it takes maybe
20 hard strokes to move an inch. Last night I tried heat, a 60 watt bulb in a 10" reflector laid on the floor. It helped a bit, in 15 min it would soften the circle under the reflector with only a hint of scorching of the underlaying particle board. 30 min would definitely scorch the floor.

Is there an easier way to do this? I'm at wit's end.


There is a tool like the one you're using but driven by an air hammer. Home Depot rents them, IIRC.

Recently done ours. Used a hot air paint stripper gun and a scraper like yours. Our's were on concrete which may have been easier that particle board. It takes a while.

John

Hey Nick,

Not a lot better or faster, but try a steam-iron, like the one the domesticated person in your family uses to iron shirts and pants, etc. Set to high heat, on a damp cloth, apply steam as fast as the iron will generate it. You can get into a nice bit of a rhythm where you can move the iron to a "new spot" and lift where it has just been, and repeat. Repeat....ad nauseum!! Then if necessary you start all over on the paper left behind, but it is much easier to steam and lift. Don't ask how I know about doing this, but be advised we're to get delivery of a large quantity of new flooring today.

It won't actually make the iron unsuitable for doing clothes in future either, but even if it does, the 25 bucks for a new iron is well worth it, and you get the old one for lots of good uses in the shop. Helps get some gluey stickers off, and does a fair job of heating bearings for installation on a shaft. Not as nice as an electric fry pan, but not bad.

Take care.

Brian Laws>About 20 years ago my wife laid our living-dining room in floor tiles,

Try this,

formatting link
I used this tool to strip MANY layers of paint from my house and it works great. The company claims that it will also work on floor tiles. I only used it on paint with very good results.

Shawn

I've heard that dry ice placed on the tile can cause them to pop up. Never tried it myself.

Heat will soften the glue, dry ice will make it brittle. A propane torch worked pretty good for me .

A clothes iron works too if a flame is a bad idea in the space you are working in.

||About 20 years ago my wife laid our living-dining room in floor tiles, ||12" squares of linoleum glued down. Now we need to remove the tiles and ||it is becoming a major PITA. Some areas of the tiles come up pretty ||easy, but a lot of areas have to be chipped up at great labor. I'm ||using a shovel-like METAL tool designed for the purpose with a ||resharpenable blade about 7" wide and in the tough areas it takes maybe ||20 hard strokes to move an inch. Last night I tried heat, a 60 watt ||bulb in a 10" reflector laid on the floor. It helped a bit, in 15 min ||it would soften the circle under the reflector with only a hint of ||scorching of the underlaying particle board. 30 min would definitely ||scorch the floor. || ||Is there an easier way to do this? I'm at wit's end.

Try dry ice. Break it into chips, pour on floor. Wiat 15 seconds, then sweep the ice to another section. Smack the cold area with a hammer, sweep the chips aside. I've not tried this on a floor, but it works great to remove asphalt-based sound deadener from race car projects. In that application, I use an air chisel with a dull blade. I can do an entire car in under an hour. Texas Parts Guy

I needed to take up tile, with "sheet goods" glued underneath it. I went and bought a Husky air chisel for $25. I believe it is one of the top ten tool choices I have made in my ENTIRE life.

Still a lot of work, but only 1/10th or less of what it would have been with other methods. Find one from a friend, rent one, or just bite the bullet and buy one. They are useful for a lot of things other than tile, and a handy tool.

Steve

They make a heat gun just for floor tile removal. One of our techs borrowed one of our 1000 degree ones(used for heat shrink tubing) for the weekend, he had some bathroom tiles to remove. It worked, but he said he had a heck of a time getting the smoke out...

Stan

A few months back I faced a similar problem.

Home Depot, and other places, will rent a device called a "Salamander". It is a long, heavy, bent metal pipe with an air fitting on one end and a air hammer on the other end. There is a special Salamander blade, about 6" wide HSS. This tool works well but is expensive.

You can buy a Salamander blade and a wide chisel blade for various demolition hammers. Grind the chisel blade so it can hold the Salamander blade and you have a 6" wide electric chisel with an easy-to-replace blade. I did this for my neighbor's Milwaukee demo hammer, using a Bosch spine drive 4" chisel.

The solution I used at home was to get a Salamander blade a 5" square section of 1/2" plate, some 2" square tubing a 3/4 NPT floor flange and a section of 3/4 pipe. Weld the plate, tube and flange together so the mass is low and the blade connects to the pipe. Have at it manually.

My father made something similar with a 3" leaf spring and a

6' wrecking bar. The leaf spring can be cut cold and sharpened quite well. But 3" is just too narrow and will dig into the floor.

formatting link
Though I usually use a powerful heat gun and a heavy duty putty knife

Gunner That rifle hanging on the wall of the working-class flat or labourer's cottage is the symbol of democracy. It is our job to see that it stays there. - George Orwell

Dry ice works,you then hit the tiles with a hammer and it shatters into pieces.

On Thu, 24 Jun 2004 21:19:51 GMT, Gunner calmly ranted:

FWIW, HF's heat gun is on sale right now for $12.99 in the flyer. I bought one from them 18 years ago and it's still going strong. I used it for removing the asphalt-based linoleum in my 50+ y/o bathroom when I lived in Vista. I also used it for removing 12 coats of paint from the kitchen cabinets and doors. They're very useful, well worth the price!

------------------------------------------------------ I survived the D.C. Blizzard of 2000...from California. ----------------------------

formatting link
Comprehensive Website Development --------------------------------------------------

You might try cold. I took up old tiles with the tool you describe, they were brittle and came up easily. If your tiles are more flexible, they might be harder to pull up for that reason. Cold might simulate that a bit.

Of course, how you get cold right now is another issue.

Mine is meant for paint stripping.

John

Don't let your wife see you doing this. She will think you can iron clothes next!

John

Thanks to all you guys for the many helpful suggestions, I'm working on several of the heat solutions now.

The Harbor Freight Air Scraper sounds very interesting, but I'm worried about it's effect on the underlying particle board. What are the particle boards chances of surviving such a powerful tool? Yes, I know I never should have used particle board anywhere in the house,, but the original plan was to put a rug over it and it's done now and can't be easily undone.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required