Tool Guide

Stole this from anther forum I frequent...
Tool Guide:
HAMMER; Originally employed as a weapon of war, the hammer nowadays is used
as a kind of divining rod to locate expensive parts not far from the object we are trying to hit. MECHANIC'S KNIFE; Used to open and slice through the contents of cardboard cartons delivered to your front door; works particularly well on boxes containing leather and fabric products.
ELECTRIC HAND DRILL; Normally used for spinning steel Pop rivets in their holes until you die of old age, but it also works great for drilling mounting holes in fenders just above the brake line that goes to the rear wheel.
PLIERS; Used to round off bolt heads.
HACKSAW; One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.
VISE-GRIPS; Used to round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.
OXYACETYLENE TORCH; Used almost entirely for lighting various flammable objects in your garage on fire. Also handy for igniting the grease inside a brake drum you're trying to get the bearing race out of.
WHITWORTH SOCKETS; Once used for working on older British cars and motorcycles, they are now used mainly for impersonating that 9/16 or 1/2 socket you've been searching for the last 15 minutes.
DRILL PRESS; A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your drink across the room, splattering it against that freshly painted part you were drying.
WIRE WHEEL; Cleans rust off old bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprint whorls and hard-earned guitar calluses in about the time it takes you to say, 'Ouc....'
HYDRAULIC FLOOR JACK; Used for lowering a tractor to the ground, trapping the jack handle firmly under the chassis somewhere.
EIGHT-FOOT LONG DOUGLAS FIR 4X4; Used for levering a tractor upward off a hydraulic jack handle.
TWEEZERS; A tool for removing wood splinters.
PHONE; Tool for calling your neighbor to see if he has another hydraulic floor jack.
SNAP-ON GASKET SCRAPER; Theoretically useful as a sandwich tool for spreading mayonnaise; used mainly for getting dog-doo off your boot.
E-Z OUT BOLT AND STUD EXTRACTOR; A tool that snaps off in bolt holes and is ten times harder than any known drill bit.
TIMING LIGHT; A stroboscopic instrument for illuminating grease buildup.
TWO-TON HYDRAULIC ENGINE HOIST; A handy tool for testing the tensile strength of ground straps and brake lines you may have forgotten to disconnect.
CRAFTSMAN 1/2 x 16-INCH SCREWDRIVER; A large motor mount prying tool that inexplicably has an accurately machined screwdriver tip on the end without the handle.
BATTERY ELECTROLYTE TESTER; A handy tool for transferring sulfuric acid from a car battery to the inside of your toolbox after determining that your battery is dead as a doornail, just as you thought.
AVIATION METAL SNIPS; See hacksaw.
TROUBLE LIGHT; The mechanic's own tanning booth. Sometimes called a drop light, it is a good source of vitamin D, 'the sunshine vitamin,' which is not otherwise found under tractors at night. Health benefits aside, its main purpose is to consume 40-watt light bulbs at about the same rate that 105-mm howitzer shells might be used during, say, the first few hours of the Battle of the Bulge. More often dark than light, its name is somewhat misleading.
PHILLIPS SCREWDRIVER; Normally used to stab the lids of old-style paper-and-tin oil cans and splash oil on your shirt; can also be used, as the name implies, to round off Phillips screw heads.
AIR COMPRESSOR; A machine that takes energy produced in a coal-burning power plant 200 miles away and transforms it into compressed air that travels by hose to a Chicago Pneumatic impact wrench that grips rusty bolts last tightened 60 years ago by someone in Dearborn, and rounds them off.
PRY BAR; A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.
HOSE CUTTER; A tool used to cut hoses 1/2 inch too short.
Regards, Joe Agro, Jr. (800) 871-5022 http://www.AutoDrill.com http://www.Multi-Drill.com
V8013
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload
wrote: Greetings Joe, The last week has been very bad for me. Yesterday I thought I was going insane. Feeling better today and reading your post made me laugh until tears flowed and now my stomach hurts. Thank You, Thank You, Thank You. Cheers, Eric R Snow

Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

You are welcome as far as the posting of it goes... But I ahven't a clue who wrote it. I stole it from a user in a motorcycle forum. :)
Hope you have a better week... A MUCH better week...
--


Regards,
Joe Agro, Jr.
  Click to see the full signature.
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

Dunno about the source but it's been around for a while: I first saw it here about 5 years ago...
It's truly hilarious! <Pun deliberate!>
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload
"RAM^3" wrote:

Some of those tools are useful for turning specialty bolts: http://eccentrix.com/members/jfcole/bolts.htm
Jon
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

Come to think of it I've got a few of those around here, somewhere!
I could have used some of those "Type B Adapters in 1/2 x 3/8 x 2" a few months ago. <G>
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

Polytechforum.com is a website by engineers for engineers. It is not affiliated with any of manufacturers or vendors discussed here. All logos and trade names are the property of their respective owners.