⏣ General Metalworking

30777 Threads Posts
to

Drilling/tapping endholes in long rectangular bar

Awl-- Will be doing this on a semi-production basis, god willing. Material: roughly 3/4 x 1.5 alum, 40-48" long; one or...
18 comments posted 21yrs
posted by physical
18 comments posted 21yrs posted by physical

Found something weird inside my saw

Hi all, Today I found something weird inside the vice of my power hacksaw. I've noticed a rubber boot inside the vice b...
17 comments posted 21yrs
posted by cdt22NOSPAM
17 comments posted 21yrs posted by cdt22NOSPAM

Cutting "square" holes in sheet metal?

How would I go about cutting small 1/4 inch square holes in 10 gauge sheet sheet metal?
17 comments posted 21yrs
posted by pr7820
17 comments posted 21yrs posted by pr7820

Chucker Project-Gunner?

I just read your last post from a month ago about not using cog belt for spindle but I had already installed the cog an...
8 comments posted 21yrs
posted by tradewind
8 comments posted 21yrs posted by tradewind

Closeouts on medium power cordless drill?

I have a project at work where I need a 14.4 volt (or 15.6 volt)cordless drill with 1/2 inch collet. It should have 2 b...
0 comments posted 21yrs
posted by eganders
0 comments posted 21yrs posted by eganders

Acu-rite DRO scale

Does anyone have dimensions of the alignment bracket that is used when installing an AR-5 DRO scale, which holds the re...
1 comments posted 21yrs
posted by davefc
1 comments posted 21yrs posted by davefc

OT firepiston metal content some were made of brass

Anyone here made a working firespiston? http://www.onagocag.com/piston.htmlI've tried a couple times but never got anywh...
1 comments posted 21yrs
posted by kfvorwerk
1 comments posted 21yrs posted by kfvorwerk

Emerson Horizon 1 VFD info request

I just finished installing an Emerson Horizon 1 singlephase to 3phase VFD on my big Delta drillpress. Its only rated fo...
5 comments posted 21yrs
posted by gunner
5 comments posted 21yrs posted by gunner

welding Q

OK, so think of a cheap Harbor Freight compressor with the motor and piston sitting above the tank. Now think of me as...
12 comments posted 21yrs
posted by waldhorn
12 comments posted 21yrs posted by waldhorn

Carbonator questions (TIG torch cooler)

I finally received a carbonator pump. As a nice extra, included was a water/co2 charging tank, for which I have no use...
8 comments posted 21yrs
posted by ignoramus4939
8 comments posted 21yrs posted by ignoramus4939

OT toyota tacoma "meteor proof" tv commercial

just saw this one on tv. humor is a subjective thing but i thought it was one of the funniest tv commercials of all tim...
6 comments posted 21yrs
posted by wwixon
6 comments posted 21yrs posted by wwixon

looking for new and used Metric endmills

looking for new and used Metric endmills preferred the carbide and if coated TIALN. also if anyone have cobalt rods (no...
0 comments posted 21yrs
posted by kh_khayat
0 comments posted 21yrs posted by kh_khayat

steel swing gate question

I am drawing up a steel wrought-iron style gate, can anyone point me to a website that shows strengths needed for the c...
9 comments posted 21yrs
posted by ralloha2
9 comments posted 21yrs posted by ralloha2

Total newbie needs help

Two questions... How do I measure the gauge of sheet metal... for example, what would be the gauge of the sheet metal s...
10 comments posted 21yrs
posted by tomwoodman42
10 comments posted 21yrs posted by tomwoodman42