⏣ General Metalworking

30777 Threads Posts
to

free stuff - vaguely metal related

free, just pay postage item 1 - 65 chevy wheel cylinder - I used to keep one of these trucks going for a friend - cylin...
0 comments posted 21yrs
posted by william_b_noble
0 comments posted 21yrs posted by william_b_noble

Brake Fluid - Alternative Use?

The metalworking content is that I bought two old cans of brake fluid for the metal cans. One will be used for Ed's Red...
28 comments posted 21yrs
posted by GeoLane_NOSPAM_
28 comments posted 21yrs posted by GeoLane_NOSPAM_

Bridgeport Wiring help?

Our school has been offered a Bridgeport Milling Machine (S #BR-251009). It is currently wired to 3 phase 440V. I would...
0 comments posted 21yrs
posted by Rees2001.1wob63
0 comments posted 21yrs posted by Rees2001.1wob63

Capacitor start motor help please

I have a grinder that has been in the box for a little over six years now. I bought it new a couple weeks before I had...
18 comments posted 21yrs
posted by tesnow
18 comments posted 21yrs posted by tesnow

oxygen/acetylene gouging tips?

I am now the owner of quite a few oddball torch tips, all of which fit my Airco torch. Ernie was telling me yesterday a...
3 comments posted 21yrs
posted by grant
3 comments posted 21yrs posted by grant

cleaning NOS cutting torch tips

I got a lot of really old but almost entirely unused Airco torch tips today. Many are of a kind I've never seen before....
26 comments posted 21yrs
posted by grant
26 comments posted 21yrs posted by grant

Thoughts on Colchester 6535 Lathe?

Hi Gang, I have been asking a lot of questions over the past few days as I try to figure out what lathe works best for...
4 comments posted 21yrs
posted by jbacc
4 comments posted 21yrs posted by jbacc

Colchester Model 6535 Lathe/Opinions Please

Hi Gang, I have been asking a lot of questions over the past few days as I try to figure out what lathe works best for...
8 comments posted 21yrs
posted by jbacc
8 comments posted 21yrs posted by jbacc

more encoder mounting thoughts

Friday afternoon saw the arrival of several diameters and types of cable from McMaster-Carr. My plan is to use this cab...
1 comments posted 21yrs
posted by etpm
1 comments posted 21yrs posted by etpm

Machinist trainee success

So I've had this kid working for me for a while now. He does not have the same work ethic I had at his age. But he is g...
6 comments posted 21yrs
posted by etpm
6 comments posted 21yrs posted by etpm

Newbie taper qurestion: self-holding?

Are Morse tapers self holding against radial loads? My horizontal mill has an MT2 spindle. Would an end mill holder req...
0 comments posted 21yrs
posted by bobengelhardt
0 comments posted 21yrs posted by bobengelhardt

Half round stock

Are there suppliers of half round stock steel ? I need 1-1/2" half round in 3 foot lenghts. I could mill round stock, bu...
4 comments posted 21yrs
posted by soundadv
4 comments posted 21yrs posted by soundadv

Action Figure Scarecrow frame

Ok... so I know I should have faced all the washers, grooved them and installed o-rings... Drilled and tapped then inst...
1 comments posted 21yrs
posted by 9ekdu
1 comments posted 21yrs posted by 9ekdu

CNC on the cheap

With a box of Legos you too can mill your own toast. http://www.ozbricks.com/bobfay/bedrtl1.mov http://www.ozbricks.com/...
6 comments posted 21yrs
posted by spamto154
6 comments posted 21yrs posted by spamto154