⏣ General Metalworking

30777 Threads Posts
to

FS: 10" Sheldon Lathe Manual

Hi all, Fall cleanup around here. Offered for sale here in case someone needs or wants it... manual for the Sheldon 10"...
0 comments posted 21yrs
posted by jessehmailbox-rcm
0 comments posted 21yrs posted by jessehmailbox-rcm

fuel tank--free

ANyone need a side tank for an '85-ish Ford one ton (E350)? Located in Escondido, Ca., no shipping, sorry. bill
2 comments posted 21yrs
posted by wmartin
2 comments posted 21yrs posted by wmartin

Looking for a manual for a elta bandsaw

I just pick up a 14" delta band saw, it has the dual speed gear box for both metal/wood. I am having trouble getting fo...
4 comments posted 21yrs
posted by wayneCLEARTHISTYPE
4 comments posted 21yrs posted by wayneCLEARTHISTYPE

More thoughts on encoder mounting

Tomorrow morning I will use the laser to measure backlash and travel. But I'm pretty sure it's the rubber belt stretchi...
4 comments posted 21yrs
posted by etpm
4 comments posted 21yrs posted by etpm

Reciprocating lathe

Guys, I am about to build a reciprocating wood lathe for cutting out multiple bowls from a half log section. The bowls...
5 comments posted 21yrs
posted by jjohnson17
5 comments posted 21yrs posted by jjohnson17

Request for help with steel shaft deflection problem

Hello everyone, I have a 2mm OD hardened steel dowel pin used as a bushing shaft, that is 0.505" inches long. Each end...
14 comments posted 21yrs
posted by johnjmechanical
14 comments posted 21yrs posted by johnjmechanical

Problem notching pipe with floor drill press

This is my first notching operation. Nothing fancy, just a straight notch at 90 degrees with my new floor drill press (...
6 comments posted 21yrs
posted by Fred
6 comments posted 21yrs posted by Fred

Encoder report w/oscilloscope

Ned, I went ahead and supplied 5 volts to the encoder and followed your instructions for scope use. I could watch the t...
15 comments posted 21yrs
posted by etpm
15 comments posted 21yrs posted by etpm

More oscilloscope help please Ned

Greetings Ned, In your post about the scope you say to have the display turned off. The encoder still needs power though...
10 comments posted 21yrs
posted by etpm
10 comments posted 21yrs posted by etpm

Best way (most efficient) way to heat my studio?

hey everyone, Winter's right around the corner and after 2 years without studio heat, I MAY finally be able to do somet...
27 comments posted 21yrs
posted by SP-AMB-LOCKrainlover
27 comments posted 21yrs posted by SP-AMB-LOCKrainlover

Invitation to a pictorial tour of my New Shop!

Hi Folks, It's been a while since I've posted to this group. Just finished moving to a new shop and thought people migh...
10 comments posted 21yrs
posted by ejb
10 comments posted 21yrs posted by ejb

PING: Myford

--Tried to send email to Myford Ltd this morning and it bounced! Apparently there's a redirect or something going on so...
6 comments posted 21yrs
posted by steamer
6 comments posted 21yrs posted by steamer

Will this laser idea work? On topic

This may seem off topic but it's not really. Measuring is important to machining. And I need to make a measurement with...
44 comments posted 21yrs
posted by etpm
44 comments posted 21yrs posted by etpm

1/2" poly burst pressure

What is the burst pressure of 1/2" black poly tubing rated for 100psi. I want to bury it as an air line between my hous...
24 comments posted 21yrs
posted by habbi
24 comments posted 21yrs posted by habbi

1/2 hp single phase 110v motor--free bronx

pickup in bronx and it's yours will ship but i need shipping costs covered wights about 40 pounds snipped-for-privacy@ea...
0 comments posted 21yrs
posted by plener
0 comments posted 21yrs posted by plener