⏣ General Metalworking

30777 Threads Posts
to

Cutting aluminum using carbide saw

Hi to all, Someone at the metalshop where i was buying a few aluminum flat bar tell me that aluminum (series 6000) coul...
17 comments posted 21yrs
posted by andre.langevin
17 comments posted 21yrs posted by andre.langevin

any value or use in a key cutter?

I posted earlier about the Benchmaster Key Cutter, Mocel MH2. I didn't get many responses, leading me to assume there i...
16 comments posted 21yrs
posted by cusmarsh
16 comments posted 21yrs posted by cusmarsh

Marking steel

I would like to know what you use for marking/writing on steel... I know that I could use chalk, but I was looking for...
19 comments posted 21yrs
posted by ignoramus14408
19 comments posted 21yrs posted by ignoramus14408

Forming Stainless Steel

I have a fabricated lawnmower that has the top deck corroded through, and I decided to replace it with a sheet of stain...
7 comments posted 21yrs
posted by nospam.clare.nce
7 comments posted 21yrs posted by nospam.clare.nce

Toolholders

I was looking at a small Fray 'All Angle' model 2. It uses tool holders that I did not recognize. The taper section is 2...
0 comments posted 21yrs
posted by spamless
0 comments posted 21yrs posted by spamless

New stuff at NEMES and "Just when you think"

New pictures on the NEMES web site ( www.neme-s.org ) are pictures from Rollie Gauchers open house, the Yankee Steam Up...
5 comments posted 21yrs
posted by errol.groff
5 comments posted 21yrs posted by errol.groff

Problem with Motor Starter

I just rewired my wood lathe from 440v to 220v three phase. I also rewired the transformer for 220v primary to 115v sec...
1 comments posted 21yrs
posted by Sierevello
1 comments posted 21yrs posted by Sierevello

Force feedback shuttle control

I have a couple of small steppers -- 20 oz in or thereabouts -- that I think would serve dandy as force feedback motors...
3 comments posted 21yrs
posted by boat042-spam
3 comments posted 21yrs posted by boat042-spam

Fuel tank rust removal / sealer

The rust removal question gets beaten around here periodically but I have a variation on the theme. I'm wondering if an...
13 comments posted 21yrs
posted by GeoLane_NOSPAM_
13 comments posted 21yrs posted by GeoLane_NOSPAM_

3ph Welder-RPC update

I posted before that Id made a quicky rotary phase converter for a 3 phase welder out of a 10hp 3450 rpm new motor and...
7 comments posted 21yrs
posted by gunner
7 comments posted 21yrs posted by gunner

240V -> 208V -- How to?

I am seriously looking at a Miele front load washer. It uses 208V and you have to buy a $200+ "adaptor" in order to use...
9 comments posted 21yrs
posted by dantzler34
9 comments posted 21yrs posted by dantzler34

Wiring Phase-a-Matic to Bridgeport

Hi, I have wired a Heavy Duty Phase-a-Matic 1-3hp to my Bridgeport 1J 1hp motor. I want to make sure that I have done t...
1 comments posted 21yrs
posted by Bothunter
1 comments posted 21yrs posted by Bothunter

layout question - bolt hole pattern

I need some guidance on figuring out what the bolt hole co-ordinates are to build a drive flange. The hub I need to bol...
16 comments posted 21yrs
posted by rbce2003
16 comments posted 21yrs posted by rbce2003

Question on Bussman Fuses BAF2 and FNM2

I blew the fuse on my Powermatic lathe today when I miswired a component in the circuit. The original fuse was probably...
13 comments posted 21yrs
posted by Sierevello
13 comments posted 21yrs posted by Sierevello

fa: minarik DC drive

here's the link http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=7551003555 partially tested, so bid accordingly
0 comments posted 21yrs
posted by william_b_noble
0 comments posted 21yrs posted by william_b_noble