⏣ General Metalworking

30777 Threads Posts
to

Zinc Metal Test

Hi I have a piece of metal that i am trying to identify if it is Zinc or not. I did the following tests 1 It doesn't st...
5 comments posted 21yrs
posted by abcd
5 comments posted 21yrs posted by abcd

OT - Faulty odometer reading - 05 Buick

I finally broke down and bought a new buick, 05 LeSabre, and got rid of my old car with more miles than I care to think...
21 comments posted 21yrs
posted by billwhitley
21 comments posted 21yrs posted by billwhitley

Sufficient material for aquarium stand

I have a heap of just slightly undersized 3/8" steel roundstock, and have been kicking it around on using it to make an...
1 comments posted 21yrs
posted by not
1 comments posted 21yrs posted by not

5th Wheel Hich Position?

A fifth-wheel trailer is one that has a hitch that connects to the towing vehicle at a point above the rear axle of the...
6 comments posted 21yrs
posted by nehmo54
6 comments posted 21yrs posted by nehmo54

Found a great website

You should check out the tools at www.b2bprofessionaltools.com Great site.
19 comments posted 21yrs
posted by thomassaccuci
19 comments posted 21yrs posted by thomassaccuci

Practical Oxy Acetyline Welding 1938 FA

Great old Welders handbook from 1938 by R Granjon,P Rosemberg & A Desgranges. Pub. The Welding Journal ,(Raggett & Co.)...
0 comments posted 21yrs
posted by evans_susie
0 comments posted 21yrs posted by evans_susie

Best way to level gravel turn around

I bought some wood grade stakes. What is the best way to use them? Just put them with a linve indicating the level I wan...
21 comments posted 21yrs
posted by stryped
21 comments posted 21yrs posted by stryped

Selenium Rectifier replacement

I need to replace the selenium rectifier stack in an old battery charger to bring it back to life. The battery charger...
20 comments posted 21yrs
posted by bradandlee
20 comments posted 21yrs posted by bradandlee

Anyone need any HiTemp wire?

I scounged up a few rolls of fabric coated hi temperature wire, from 18ga to 10ga. Plus a few that appear to be plastic...
10 comments posted 21yrs
posted by gunnerNOSPAM
10 comments posted 21yrs posted by gunnerNOSPAM

OT-Bin priced dvds

Does anyone know why the soundtracks from old tv series like Dragnet are not the originals?I bought Dragnet in Walmart...
0 comments posted 21yrs
posted by SAYWAT
0 comments posted 21yrs posted by SAYWAT

Seneca Falls lathe value?

I sure hope someone can help me out here. I just looked at what appears to be a 14x36 lathe produced in the 30's (could...
12 comments posted 21yrs
posted by dgrup
12 comments posted 21yrs posted by dgrup

phase converters

I realize the extent of my confusion about phase converters. I thought that phase converters were motors/generators cou...
53 comments posted 21yrs
posted by ignoramus4745
53 comments posted 21yrs posted by ignoramus4745

cut tee slots with a shaper

Hi all, I have recently got a shaper in my H/ws, one of the projects I would like to do is a t slotted cross slide for...
7 comments posted 21yrs
posted by shedfull66
7 comments posted 21yrs posted by shedfull66

Ping Ryan in San Fernando- Air Compressor

Ryan..Ive been emailing you about air compressors. I got you one. I got you a pretty nice C-H, on a 60 gal verticle tan...
0 comments posted 21yrs
posted by gunner
0 comments posted 21yrs posted by gunner