⏣ General Metalworking

30777 Threads Posts
to

tap drill for 1/16 -27

I need to make a threaded hole with a 1/16-27 thread. I have the tap, but have looked up in the handbooks I have and ca...
4 comments posted 21yrs
posted by desperado_48m
4 comments posted 21yrs posted by desperado_48m

SME WESTEC trade show ENCO booth

hello, i was wondering if anyone is planning on attending the SME Westec trade show next week in southern california. i...
0 comments posted 21yrs
posted by mpskate
0 comments posted 21yrs posted by mpskate

shoulder screws?

Does anyone know a source for small quantities of socket-head shoulder screws? Thanks!
5 comments posted 21yrs
posted by groundzero
5 comments posted 21yrs posted by groundzero

Meco Midget Torch Holder

Made from a piece of a junked computer case. A little cutting with the bench shear, jewelers saw and bending on the bra...
0 comments posted 21yrs
posted by llhote
0 comments posted 21yrs posted by llhote

Need Thompson 2F Grinder Info

I would like to buy any manuals or other info for a Thompson 2F 8"x24" hydraulic surface grinder. Particularly need inf...
2 comments posted 21yrs
posted by notme
2 comments posted 21yrs posted by notme

OT shotgun shell

While walking to train this morning, I found a shotgun shell on the street. 12 ga 3.25", it would fit my shotgun. The q...
6 comments posted 21yrs
posted by ignoramus29361
6 comments posted 21yrs posted by ignoramus29361

need bigger nuts

I have an old woodworking lathe with a 3/8" fine thread tailstock spindle instead of a taper. I bought a Morse tapered...
6 comments posted 21yrs
posted by shawn
6 comments posted 21yrs posted by shawn

OT anyone work on Mahindra tractor?

My dad has one about 4 years old that has developed an intermittant starting problem. WHen turning the key I can fell s...
0 comments posted 21yrs
posted by stryped
0 comments posted 21yrs posted by stryped

Sewing Machine Mods

Hey, did you know the throat on a sewing machine is usually more than 5 1/2 inches? This means you can sew booklets and...
22 comments posted 21yrs
posted by DGoncz
22 comments posted 21yrs posted by DGoncz

desiccant supplier?

Hi, I would like to get a couple little bags of silica desiccant to keep with my squares and straight edge. Where can I...
11 comments posted 21yrs
posted by petermichaux
11 comments posted 21yrs posted by petermichaux

OT Frivolous lawsuits again (tort reform)

All kinds of skunks are out there, suing manufacturers. Check out the story behind this home-made tramway. Reminds me o...
4 comments posted 21yrs
posted by jim_member
4 comments posted 21yrs posted by jim_member

use at home sandblaster

Hope this is the right forum for this question. I'm doing a lot of metal work on a veh. restoration. Some metal needs t...
6 comments posted 21yrs
posted by a6016
6 comments posted 21yrs posted by a6016

More Foundry Work - Posted

This section has a bit of wood work, but the new practices are etching and priming the castings with a Zinc Chromate ba...
1 comments posted 21yrs
posted by frnkgmbk
1 comments posted 21yrs posted by frnkgmbk

aluminum surface smoothness comparison?

Does anyone know a website that shows photographs of turned aluminum along with specifications? I have a requirement fo...
3 comments posted 21yrs
posted by ranger52oc
3 comments posted 21yrs posted by ranger52oc