⏣ General Metalworking

30778 Threads Posts
to

NexMill-15 part #6 - Posted

Part # 6 of the NexMill-15 project has been posted. This section is the final mounting of the Fixed Gantry, Z-Axis cast...
0 comments posted 21yrs
posted by frnkgmbk
0 comments posted 21yrs posted by frnkgmbk

Two newbie turning questions

I hope some old hands can offer me some advice here: I have a new Chinese 14x40 gearhead lathe, and it seems to be a re...
14 comments posted 21yrs
posted by rlincolnh
14 comments posted 21yrs posted by rlincolnh

How to tell what MT tailstock taper is?

If you had a largish lathe (18"x72") but didnt know the MT # of the tailstock, how would you go about figuring out what...
3 comments posted 21yrs
posted by greg
3 comments posted 21yrs posted by greg

Vise question

Hi all I want to make/buy a vise for my workbench. I was thinking about a leg vise but then I started thinking wouldn't...
4 comments posted 21yrs
posted by cramos
4 comments posted 21yrs posted by cramos

Internal splines

Hi all........ Recently I decided to attempt to produce a couple of internally splined couplings out of steel. Dim's ar...
8 comments posted 21yrs
posted by pkangas
8 comments posted 21yrs posted by pkangas

Atlas 618 leadscrew question

Hi, first of all, I'm not familiar with lathe vocabulary and use primary french as language, so excuse me the poor "tex...
6 comments posted 21yrs
posted by fproulx
6 comments posted 21yrs posted by fproulx

FA: Ramset M150 Gas Powered Pin Nailer

Not sure if anyone can use this tool, surplus to my needs! Great for shooting straps into steel or concrete, started bi...
0 comments posted 21yrs
posted by escarcegaNOSPAM
0 comments posted 21yrs posted by escarcegaNOSPAM

OT: '91 lincoln/mercury service manual

I have the factory service manual for the '91 Town Car/Crown Victoria/Grand Marquis. I am going to pitch it unless some...
0 comments posted 21yrs
posted by kevin
0 comments posted 21yrs posted by kevin

Welding alternator bracket - big oops!

Now I've gone and done it... Scored a great condition BMW 325is for a song and have been driving it for some time until...
20 comments posted 21yrs
posted by surftom
20 comments posted 21yrs posted by surftom

HF shipping times

All, What's up with Harbor *Fright* shipping? I ordered something on February 21, and according to HF customer service...
8 comments posted 21yrs
posted by Ken Sterling
8 comments posted 21yrs posted by Ken Sterling

Mower Sulky

Gang, In the dropbox, pictures of a little project I did for a local guy. He has a JD commercial walk-behind, zero-turn...
8 comments posted 21yrs
posted by Ken Sterling
8 comments posted 21yrs posted by Ken Sterling

Tin plating

Greetings, I have some old special pie baking tins which I use, but alas the tin plate has worn away and rust now stain...
12 comments posted 21yrs
posted by spurtle
12 comments posted 21yrs posted by spurtle

casting - shaw proses

Can anyone help with more information regarding the use and preparation of ethyl silica slurry. How long does it take t...
2 comments posted 21yrs
posted by nowhere
2 comments posted 21yrs posted by nowhere

Drilling Aluminium

Hi All I need to enlarge the mounting holes in a set of cast aluminium wheels from 5/8 to 17.5mm. I have a new reduced...
14 comments posted 21yrs
posted by alveyt
14 comments posted 21yrs posted by alveyt