⏣ General Metalworking

30778 Threads Posts
to

Electrical service entrance question

I built a detached backyard garage several years ago with a 200 amp service entrance fed from its own pole and transfor...
3 comments posted 21yrs
posted by tmayhugh
3 comments posted 21yrs posted by tmayhugh

What should a new 240v circuit cost?

I'm needing to get a new 240v circuit installed in my garage. I had an electrician come out, and they wanted $1000 to d...
43 comments posted 21yrs
posted by greg
43 comments posted 21yrs posted by greg

composite materials

hello, i'm wondering if anyone has suggestions for how to learn about using composite materials. i've just been astound...
4 comments posted 21yrs
posted by thefowle
4 comments posted 21yrs posted by thefowle

Should jthreadss on 4-jaw be lubricated?

I seem to have to clean the threads on my 4-jaw a lot. Chips stick to them. Could I use them dry and would that lessen t...
2 comments posted 21yrs
posted by bobengelhardt
2 comments posted 21yrs posted by bobengelhardt

Soldering loose fitting tubing/pipe

Awl-- I'm putting a 3/4 sweat fitting OVER 1/2" brass pipe, cuz, well, I think I have no choice, cuz the brass pipe wil...
9 comments posted 21yrs
posted by physical
9 comments posted 21yrs posted by physical

machining my first PCB

I wanted a 5 volt source for my newest gps, a Garmin Quest. It has a internal battery that is not intended to be servic...
4 comments posted 21yrs
posted by Billcotton
4 comments posted 21yrs posted by Billcotton

shim stock needed

I am tramming a Homier mini mill and the column is out vertically, leaning toward the front. I have exhausted all local...
21 comments posted 21yrs
posted by grady3
21 comments posted 21yrs posted by grady3

Gating Design - Study Notes Posted

More in the Metal Casting Series... http://www.theworkshop.ca/casting/course/MTB70/6/MTB706.htm Frank www.theworkshop.ca
0 comments posted 21yrs
posted by frnkgmbk
0 comments posted 21yrs posted by frnkgmbk

Mushroom valves -- where to find?

Anyone know of a source for elastomer mushroom valves? These are the little rubber discs with a stem used for one-way a...
1 comments posted 21yrs
posted by kinch
1 comments posted 21yrs posted by kinch

heat treat head?

Can an overheated aluminum engine head be heat treated (with weights on it to keep it flat) to bring back its temper and...
6 comments posted 21yrs
posted by joe_d_builder
6 comments posted 21yrs posted by joe_d_builder

Metal Pole for Eagle Scout Project

Hello Everybody! I am working on my Eagle Scout project for the Boy Scouts of America and I am looking for a metal pole...
28 comments posted 21yrs
posted by jkeagle13
28 comments posted 21yrs posted by jkeagle13

Bridgeport M-head

Any one have access to M-head parts? or know where to get them? any help is appreciated Thanks Paul
0 comments posted 21yrs
posted by ph17314
0 comments posted 21yrs posted by ph17314

welding to truck frame?

I have this buddy with a dump truck (handy thing to have). It's actually a one-ton pickup with a dump bed, which means...
12 comments posted 21yrs
posted by grant
12 comments posted 21yrs posted by grant

PTO SHaft Help

My dad just bout a used tiller for the tractor it has a small short pto shaft. It is solid square metal about 1 inch or...
7 comments posted 21yrs
posted by stryped
7 comments posted 21yrs posted by stryped