⏣ General Metalworking

30778 Threads Posts
to

OT: (Slightly) Why Women Live Longer Than Men

I just posted a picture in alt.binaries.pictures.woodworking that answers this age old mystery. Metalworking content -...
6 comments posted 22yrs
posted by bobh
6 comments posted 22yrs posted by bobh

Correct speed for a very thin slotting saw?

Hi group, I'm over halfway done (I think) with the Skeleton Wall Clock by WR Smith. I need to slot a small brass block...
2 comments posted 22yrs
posted by peekamoose
2 comments posted 22yrs posted by peekamoose

Sorghum Mill Repair

I have a friend who is trying to repair an old sorghum mill. The major problem with this machine is the condition of th...
12 comments posted 22yrs
posted by aajnorm
12 comments posted 22yrs posted by aajnorm

Shop Furness II- The Return of the Question

Has anyone here ever had any success running a standard oil furness burner on waste oil??? Through experimentation I've...
18 comments posted 22yrs
posted by howarde
18 comments posted 22yrs posted by howarde

OT-ish: furnace filters

Ok we almost never buy furnace filters (and we have three furnaces)... so I just got an idea... where can I direct Dad...
2 comments posted 22yrs
posted by tmoranwms
2 comments posted 22yrs posted by tmoranwms

Rust cleaning device

I want to make a bath I can put sticks of square tubing into, and let the bath dissolve the rust. I figger I will split...
2 comments posted 22yrs
posted by deserttraveler
2 comments posted 22yrs posted by deserttraveler

WTB Mobilith AW1 grease

I have a machine, that the manufacturer specifies Mobilith AW1 grease for coating one set of gears. I only need one 14...
7 comments posted 22yrs
posted by KLMoffett
7 comments posted 22yrs posted by KLMoffett

rust removal

can anyone tell me if potassium hydroxide is any good at removing rust? i am going to boil it(mixed with water) at about...
9 comments posted 22yrs
posted by nattydreadlocks2001
9 comments posted 22yrs posted by nattydreadlocks2001

Mill-drill spindle bearings

I need to lubricate the spindle bearings on my mill-drill (Harbor Freight, RF30) and of course the supplied "owners man...
0 comments posted 22yrs
posted by joneiserling
0 comments posted 22yrs posted by joneiserling

milling feeds

I just got around to installing the powerfeed on my ancient Bridgeport. My DRO has a function for reading the feed rate...
1 comments posted 22yrs
posted by grantNOSPAM
1 comments posted 22yrs posted by grantNOSPAM

aluminum tubing request

i am looking for aluminum tubing 8 1/4" id wall of 1/8" to 1/4". can any lister guide to where i can get it. i need 1-2...
0 comments posted 22yrs
posted by jimh720113
0 comments posted 22yrs posted by jimh720113

FA: Electric Design book (as in "code" design)

This group gets a lot of wiring questions, so there might be some interest in this auction. No disclaimer here, this is...
0 comments posted 22yrs
posted by bobengelhardt
0 comments posted 22yrs posted by bobengelhardt

Metal Working tools & Uses vintage 1930s FA

Metal work Tools handbook,hardback,no date but guess to be 1930s or earlier. Spine a little frayed but holds together f...
0 comments posted 22yrs
posted by tymontoo
0 comments posted 22yrs posted by tymontoo

Slightly OT: Craftsman screwdrivers

I opened a tool box I don't use much and all my Craftsman screwdrivers (10-15 years old) had a white opaque coating on...
17 comments posted 22yrs
posted by books4321
17 comments posted 22yrs posted by books4321

How to bend aluminum trim

I have some left over aluminum trim. I am trying to bend some to cover my patio door trim and frame so I will never hav...
1 comments posted 22yrs
posted by stryped
1 comments posted 22yrs posted by stryped