⏣ General Metalworking

30778 Threads Posts
to

SF Bay Area Combat Robotics Lab Course 9/13/2004

College of San Mateo Offers Third "Robot Challenge" Hands-On Combat Robotics Building Course in 15,000 Sq. Ft. Metal Fa...
0 comments posted 22yrs
posted by info
0 comments posted 22yrs posted by info

Please help with Agent

I try to check several newsgroups and I get the message :Finished retrieving headers. But there are no new headers. Not...
18 comments posted 22yrs
posted by etpm
18 comments posted 22yrs posted by etpm

Best choice for a 220v Buzz Box ?

Need to do some light stick welding, but am limited to the 30 Amp 220v service that my clothes dryer is hooked to (othe...
5 comments posted 22yrs
posted by malcolm
5 comments posted 22yrs posted by malcolm

Jet Lathe in Southeast Nebraska

I live in Southeast Nebraska and am looking at purchasing a Jet BDB-1340. I was wondering if anyone in the surrounding...
1 comments posted 22yrs
posted by matcamacho
1 comments posted 22yrs posted by matcamacho

Trying to ID some tools/fixtures

I've been going through some buckets of tooling I've accumulated, and here are a couple things I haven't been able to I...
8 comments posted 22yrs
posted by gto69ra4
8 comments posted 22yrs posted by gto69ra4

Recommendations for greasing gears?

In the process of fitting the vertical attachment to my Sturdimill, I note that the manual doesn't show any lubrication...
4 comments posted 22yrs
posted by a_hole_in_the_ground
4 comments posted 22yrs posted by a_hole_in_the_ground

phase converter questions

I recently bought a 1.5HP 3ph Baldor 10 inch grinder with 1/2HP 3Ph dust collector. I connected them to a Phase-a-matic...
120 comments posted 22yrs
posted by cas
120 comments posted 22yrs posted by cas

shop smithy 1239 questions

I have a shop smithy 1239 that I traded for and I am being asked to thread a rifle bbl on it. I didnt get any paperwork...
3 comments posted 22yrs
posted by whodat
3 comments posted 22yrs posted by whodat

Dumbwaiter project gone bad

I have an talanted engineering group here at work. We design and build equipment for in house use and a couple of devic...
24 comments posted 22yrs
posted by rleonard
24 comments posted 22yrs posted by rleonard

OT selling anvil and swage blocks

I want to sell my anvil and swage block 75lb cast steel anvil the surface is not smooth a set of two gray cast iron swa...
0 comments posted 22yrs
posted by kfvorwerk
0 comments posted 22yrs posted by kfvorwerk

Palmgren Rotary table

After making the mistake of purchasing an import RT from Kitts that turned out to be rubish made in India I then bought...
7 comments posted 22yrs
posted by doubleeboy
7 comments posted 22yrs posted by doubleeboy

New scam?

From an email today...an old scam with a new face? Status: U Return-Path: Received: from plesk.ev1servers.net ([66.98.1...
20 comments posted 22yrs
posted by gunner
20 comments posted 22yrs posted by gunner

opinion on this lathe?

All I have right now is a pic: http://www.metalworking.com/dropbox/YAM1440.jpg I had never heard of YAM before, but the...
2 comments posted 22yrs
posted by rick
2 comments posted 22yrs posted by rick

XYZ table for plasma cutter

Hi All, Anyone got plans to built one? please Thanks Jason
4 comments posted 22yrs
posted by J.holler
4 comments posted 22yrs posted by J.holler

Pilot talk

Just curious as I've seen several posts over the past couple years in regards to aviation. How many of you are licensed...
49 comments posted 22yrs
posted by frogge
49 comments posted 22yrs posted by frogge