⏣ General Metalworking

30778 Threads Posts
to

Grinding fingers or "dancers"

I have been given the job of grinding a .0625 dia drill blank ( M2 steel ) end down to .020 dia .25 long with a .010 ra...
3 comments posted 22yrs
posted by napdr
3 comments posted 22yrs posted by napdr

Press fit air pressure?

I'm going to press fit a .250" shaft into a bottomed (no opening on the other side) hole .249" in diameter. I'm wonderi...
4 comments posted 22yrs
posted by mboyko2000
4 comments posted 22yrs posted by mboyko2000

AJAX retrofit-update

Ok, I've been using the mill which was retrofitted with the AJAX control for a few weeks now. Still learning the conver...
7 comments posted 22yrs
posted by etpm
7 comments posted 22yrs posted by etpm

molding polyurethane?

I would like to duplicate some bushings, about 1" OD, with a ball socket ID, blind hole. Can this be molded in polyureth...
5 comments posted 22yrs
posted by NOSPAMrex
5 comments posted 22yrs posted by NOSPAMrex

Cable Guides for bicycle fork lock

With a 1 5/8 OD, my bicycle's head tube is large. With a 1 1/8 OD, my fork is medium, I think. Or large. The line tange...
1 comments posted 22yrs
posted by dgoncz
1 comments posted 22yrs posted by dgoncz

Is this any good?

http://www.grizzly.com/products/item.cfm?itemnumber=G8298
9 comments posted 22yrs
posted by bpw67deletethis
9 comments posted 22yrs posted by bpw67deletethis

Info? Devilbiss 6560 compressor

I'm being offered locally an air compressor. I'd dearly love to offload my oil-less Crapsman noisemaker and replace it...
5 comments posted 22yrs
posted by NOSPAMrex
5 comments posted 22yrs posted by NOSPAMrex

internal motor wireing question

the motor spins but not as it should, and trips the breaker. there are 6 wires in question. T11 T10 T12 T6 T5 T4 the pa...
6 comments posted 22yrs
posted by wgalcik
6 comments posted 22yrs posted by wgalcik

Hardinge DV-59 2nd Op Lathe - eBay $1 N/R

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=12577&item=2593940415 A really nice running machine too. Steve.
0 comments posted 22yrs
posted by steve
0 comments posted 22yrs posted by steve

I'm making chips at last!

Woohoo! Just gotta share... :-) I received my Chinese 7x12 today, and after a flurry of cleaning, inspecting, and lubri...
10 comments posted 22yrs
posted by tih+nr
10 comments posted 22yrs posted by tih+nr

grain in metal

Can anyone offer a short lesson in determining grain direction in metals. Thanks - Bob S.
16 comments posted 22yrs
posted by rjscibienski
16 comments posted 22yrs posted by rjscibienski

Virtual Ways?

A while back I read a reference by Don Lancaster (guru's lair; www.tinaja.com) about "Virtual Ways" for a milling machi...
12 comments posted 22yrs
posted by kccnospam
12 comments posted 22yrs posted by kccnospam

Yet another NiCd charging question

We have a 9.6v Dustbuster that lost it's NiCd batteries rather quickly, at least compared to the previous, lower voltag...
1 comments posted 22yrs
posted by bobengelhardt
1 comments posted 22yrs posted by bobengelhardt

Lathe Help

I have come by a lathe that has some electrical problems. The unit has a 2 hp 3 phase 220 volt motor. One of the magnet...
9 comments posted 22yrs
posted by bafrank
9 comments posted 22yrs posted by bafrank

Creative end cuts with no mill

I am looking for creative suggestions to cutting aluminum. I do not have a mill, and the prospects of getting one in th...
6 comments posted 22yrs
posted by shon
6 comments posted 22yrs posted by shon