⏣ General Metalworking

30778 Threads Posts
to

Get a load of this (ebay)

While listing a couple toys I had laying around from my childhood, I ran across this: http://cgi.ebay.com/ws/eBayISAPI....
11 comments posted 22yrs
posted by pkdickman
11 comments posted 22yrs posted by pkdickman

Blind Hole With a tapping head

I have a simple question but I don't know the answer. Can I use a tapping head to tap a blind hole ? thanks Mike Miller
8 comments posted 22yrs
posted by polyman
8 comments posted 22yrs posted by polyman

Gas welding questions

Hello all, I just purchased a Victor Advantage II torch outfit. I am now learning that this is considered a "light duty...
6 comments posted 22yrs
posted by fred
6 comments posted 22yrs posted by fred

Broken screw extractor?

My truck antenna snapped off due to collision with a bird. This antenna screws into the foundation, and it snapped off...
10 comments posted 22yrs
posted by ignoramus15341
10 comments posted 22yrs posted by ignoramus15341

Making capacitor safe transport plates

Hello, everybody. I have been on a new med and have lost 30 of 80 pounds overweight. I have also learned that I am diab...
3 comments posted 22yrs
posted by dgoncz
3 comments posted 22yrs posted by dgoncz

propane/air capability?

What sort of performance can you get out of propane/air, and what sort of rig do you use? Hank Hill has only sold me on...
4 comments posted 22yrs
posted by kichline
4 comments posted 22yrs posted by kichline

Bandsaw recommendation for 6" Alu Rounds

After 4 months of hard work, I killed off my Enco 7x12 bandsaw cutting 6" Aluminum rounds and 3" 4140 rounds. It worked...
1 comments posted 22yrs
posted by youngwerth
1 comments posted 22yrs posted by youngwerth

Anyone here do "custom" work?

Hi there, I need a small piece of work made. It doesn't matter what it is made out of - mild steel, aluminum, etc. It i...
0 comments posted 22yrs
posted by ravensforge
0 comments posted 22yrs posted by ravensforge

Stero Specticles for MARS (how to make?)

i am looking for some red and green transparent material and am wondering if any here has been able to view the stereo p...
9 comments posted 22yrs
posted by loren
9 comments posted 22yrs posted by loren

propane/air vs propane/oxygen?

OK, this is a question I've wondered about for a long time, which surfaced when I was thinking about the rosebud torch...
26 comments posted 22yrs
posted by grantNOSPAM
26 comments posted 22yrs posted by grantNOSPAM

U-Haul Trailers and Ford Explorers Don't Mix

Be advised that U-Haul will no longer rent a trailer to be towed behind a Ford Explorer. http://www.wnep.com/Global/stor...
11 comments posted 22yrs
posted by jstewart
11 comments posted 22yrs posted by jstewart

Need material for way wipers

Hello, all, I am doing the last little touches of rebuilding my Sheldon 15" lathe, and need the material for the way wi...
13 comments posted 22yrs
posted by elson
13 comments posted 22yrs posted by elson

Center held in 5C collet?

I would like to make a headstock center for my SB 10L but lacking a taper attachment, I don't think I can get the taper...
21 comments posted 22yrs
posted by walter_munney
21 comments posted 22yrs posted by walter_munney

Mitutoyo Digital Caliper

I recently acquired an old one (model 500-421 CD-S6), and I'd like to ask: does ANYONE know how to access/change the ba...
6 comments posted 22yrs
posted by marc
6 comments posted 22yrs posted by marc

Oxy/Acet torch question

Looking for some recommendations from the group. I am looking for a torch head for my oxy-acet set-up that will produce...
13 comments posted 22yrs
posted by email-rbce2003
13 comments posted 22yrs posted by email-rbce2003