⏣ General Metalworking

30779 Threads Posts
to

Fire Extinguisher accident update

I have had quite a few folks email me and also post and ask the question, so I guess its only fitting to sum it all up...
0 comments posted 23yrs
posted by chipmkr
0 comments posted 23yrs posted by chipmkr

Procedure for repalcing headstock bearings on a Myford?

I'm rebuilding a Myford ML4 (3.75" centre height) lathe at present. When I bought the lathe I found, too late, that the...
0 comments posted 23yrs
posted by a_hole_in_the_ground
0 comments posted 23yrs posted by a_hole_in_the_ground

Tubing Roller Progress Report

A progress report (painfully slow progress) on my "Ernies" tubing roller has been posted to the Metalworking.com drop b...
2 comments posted 23yrs
posted by errol.groff
2 comments posted 23yrs posted by errol.groff

Carolina Horizontal Bandsaw

Hi Folks! I wonder if anyone knows whether or not the Carolina Tool and Equipment company still does business? I have o...
3 comments posted 23yrs
posted by misty.foley
3 comments posted 23yrs posted by misty.foley

Help tuning small Bone parts

I am trying to turn string pins for a guitar out of ebony and bone. They are about inch long .290 at round part on top...
4 comments posted 23yrs
posted by drandall
4 comments posted 23yrs posted by drandall

10K vs 10L Taper Attachments

Anyone know if taper attachments for South Bend 10K and 10L lathes are interchangeable? I have a line on a taper attach...
2 comments posted 23yrs
posted by y2k
2 comments posted 23yrs posted by y2k

Wrought Iron Book?

Hi, Can anyone recommend a good book for making furniture, gates, plant pots etc. from wrought iron? Seen several on Am...
5 comments posted 23yrs
posted by feckinstupid
5 comments posted 23yrs posted by feckinstupid

digital scales for bench mills

Hello all Has anyone seen a vender in the US or Canada for these units??
10 comments posted 23yrs
posted by jpcrombie
10 comments posted 23yrs posted by jpcrombie

Any other small turbine builers still active?

Hello: I've completed several pulsejets and small turbines from plans, looking for new or larger challenges. Al
6 comments posted 23yrs
posted by alldoyle
6 comments posted 23yrs posted by alldoyle

Putting rivits in aluminum lawn chairs?

Anybody know whether the riviting tool used for putting rivits in aluminum lawn chairs is common and where the specific...
4 comments posted 23yrs
posted by Usenet
4 comments posted 23yrs posted by Usenet

replaning lathe beds

I wrote a long post about replaning lathe beds and then I don't know what happenned to it. If it went out it went out w...
6 comments posted 23yrs
posted by hagenpault
6 comments posted 23yrs posted by hagenpault

Surface Grinder: FREE to good home

I have a LaSalle Surface Grinder 6 x 18 manual. Don't have room for it anymore. It needs some minor TLC as it leaves ch...
4 comments posted 23yrs
posted by karltownsend.NOT
4 comments posted 23yrs posted by karltownsend.NOT

homebrew deburrer (bowl)?

a post down the thread (harold's response to broken tap) made a passing comment about parts deburring .. anyone try the...
0 comments posted 23yrs
posted by antoniogatta
0 comments posted 23yrs posted by antoniogatta

3 jaw chuck for Sheldon Lathe

A buddy got a very nice 10x24 Sheldon Lathe, about 1960 vintage with quite low useage. Quick change, single phase, some...
7 comments posted 23yrs
posted by spamless
7 comments posted 23yrs posted by spamless

Looking for ceramic sharpening rods source

I am looking for source of alumina ceramic rods. (Fine, medium and coarse grit. Size: 3/8" diam. 8" length) Does any on...
1 comments posted 23yrs
posted by alexkuzn
1 comments posted 23yrs posted by alexkuzn