0 comments
posted 14yrs
posted by jonbanquer
⏣ General Metalworking
30752 Threads
Posts
to
36 comments
posted 14yrs
posted by rhvp65
Overhead welding on a semi trailer
I have a "beavertail double drop deck semi trailer": http://igor.chudov.com/tmp/Trailking/ that needs some work done on...
13 comments
posted 14yrs
posted by ignoramus18965
13 comments
posted 14yrs
posted by ignoramus18965
need large bolts
I'm in need of several 3/4 x 10 bolts. Local fleet farm don't go that big. McMaster just scared me off. Any suggestions?...
40 comments
posted 14yrs
posted by karltownsend.NOT
40 comments
posted 14yrs
posted by karltownsend.NOT
Hold-down of thin material to CNC mill
Hi, all:- What's a good way to hold down material such as thin aluminum panels (eg. 1/16" or 1/8") while through-CNC mi...
18 comments
posted 14yrs
posted by speffSNIP
18 comments
posted 14yrs
posted by speffSNIP
Spray painting ?
Is a gast pump suitable for use as a air supply to run a spray paint gun? Do i need to add a air tank to smooth out the...
12 comments
posted 14yrs
posted by H.Beal
12 comments
posted 14yrs
posted by H.Beal
shop press design
I'm building a shop press about like this one: http://www.northerntool.com/shop/tools/product_604_604 I found tons of 8...
6 comments
posted 14yrs
posted by karltownsend.NOT
6 comments
posted 14yrs
posted by karltownsend.NOT
From flowchart to ladder
From flowchart to schematic to ladder I can design machine control circuits using relay logic but it's a grueling job f...
46 comments
posted 14yrs
posted by mars
46 comments
posted 14yrs
posted by mars
Fork lift info
Someone here was a certified forklift repair tech. I've lost the history. I bought an old (1978) ClarkLift 2000lb machi...
17 comments
posted 14yrs
posted by lloydspinsidemindspring.com
17 comments
posted 14yrs
posted by lloydspinsidemindspring.com
Sewer pipe failing - suggestions?
A week ago, on of my neighbors had his sewer back up into his basement. His house was built at the same time as mine (a...
69 comments
posted 14yrs
posted by rangerssuck
69 comments
posted 14yrs
posted by rangerssuck
Clearance for tapping
And speaking of tapping, how close to an edge can I tap? There's been a few times where I've drilled a hole close to an...
5 comments
posted 14yrs
posted by tim
5 comments
posted 14yrs
posted by tim
Form tapping sand cast aluminum?
To all you folks who are actually making parts from metal, I use form taps, AKA roll taps, as much as possible. I use t...
15 comments
posted 14yrs
posted by etpm
15 comments
posted 14yrs
posted by etpm
100% earning no investment no referral
Hi, I am like to show you money making system for all.. Pls sing up down websites and dollars.. Each wbsite you will ge...
0 comments
posted 14yrs
posted by onlinestar.me
0 comments
posted 14yrs
posted by onlinestar.me
OT An obituary for facts
http://www.chicagotribune.com/news/local/ct-talk-huppke-obit-facts-20120419,0,809470.story "... To the shock of most se...
24 comments
posted 14yrs
posted by anorton
24 comments
posted 14yrs
posted by anorton
smooth out calk
My project for the last week has been rebuilding an old fertilizer spreader. Its my better half's turn. All the little...
6 comments
posted 14yrs
posted by karltownsend.NOT
6 comments
posted 14yrs
posted by karltownsend.NOT