⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30754 Threads Posts
to

Question: US 220 vs Aussie 220

Bought a DoAll blade welder from Gunner last year, and finally getting around to restoring it. Wrote DoAll asking about...
59 comments posted 15yrs
posted by janders1957
59 comments posted 15yrs posted by janders1957

What are these centers called

I have a couple of centers, and while their purpose is obvious to me, I am not sure what are they called....
1 comments posted 15yrs
posted by ignoramus1471
1 comments posted 15yrs posted by ignoramus1471

Cheapest way to put up a corporate sign

What would be the cheapest way to make a sign (to be hung outside on a wall) with a corporate name. I do not want anyth...
15 comments posted 15yrs
posted by ignoramus1471
15 comments posted 15yrs posted by ignoramus1471

Lincoln electric aquires Torchmate

The acquisition of Torchmate by Lincoln Electric Holdings of Cleveland last week was prompted mainly by the rapid growt...
0 comments posted 15yrs
posted by H.Beal
0 comments posted 15yrs posted by H.Beal

OT Checkin' in on Sunday per request

I am on a roll. My last bad day was a little bit last Thursday, and that wasn't bad and only for half an hour or so. I...
4 comments posted 15yrs
posted by dforeman
4 comments posted 15yrs posted by dforeman

No new posts since Aug 1

What's going on here?
4 comments posted 15yrs
posted by gmasterman
4 comments posted 15yrs posted by gmasterman

Zero Fog mister goes internation in 10th year

Ten years ago now, I copied a Henchforth fogbuster mister and made design improvements with the help of the folks on RC...
0 comments posted 15yrs
posted by karltownsend.NOT
0 comments posted 15yrs posted by karltownsend.NOT

How to sour milk

My helper got a job. At the job, they have a communal fridge. There's one guy who will come in and help himself to most...
43 comments posted 15yrs
posted by pittmanpirate
43 comments posted 15yrs posted by pittmanpirate

Shining Aluminum

I'm redoing my boat. It's aluminum hull, painted. The gunwales are unpainted aluminum, and discolored by stain, oily ha...
10 comments posted 15yrs
posted by pittmanpirate
10 comments posted 15yrs posted by pittmanpirate

Removing Rust

I need to polish the rust off of a few joystick shafts I have and I'm not sure what kind of steel the shafts are made o...
7 comments posted 15yrs
posted by Searcher7
7 comments posted 15yrs posted by Searcher7

Diy roof repair

The shingles that Andrew Espey put up two years ago are holding up well, but the legal battle that came with them is fa...
8 comments posted 15yrs
posted by H.Beal
8 comments posted 15yrs posted by H.Beal

Trailer tire

Anyone have an extra boat wheel/tire kicking around? 5/30 x 12, 2.5 center of hole to next hole, 4.25" center of hole t...
3 comments posted 15yrs
posted by pittmanpirate
3 comments posted 15yrs posted by pittmanpirate

Welder price

What does a gently used Miller 175 MIG go for. No regulator. Works good. Steve
7 comments posted 15yrs
posted by pittmanpirate
7 comments posted 15yrs posted by pittmanpirate

Cuttermaster pictures

http://igor.chudov.com/tmp/Cuttermaster/
4 comments posted 15yrs
posted by ignoramus14275
4 comments posted 15yrs posted by ignoramus14275

AL spoolgun stuck on high

I picked up a millermatic 250 welder with an AL spoolgun at an auction a while back. I tried the spoolgun a couple days...
38 comments posted 15yrs
posted by karltownsend.NOT
38 comments posted 15yrs posted by karltownsend.NOT