⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30748 Threads Posts
to

Southtec Booth 734

If you're at Southtec check us out at Booth 734 https://sell.cncmachines.com/southtec-2019/ Afford that new machine by s...
0 comments posted 6yrs
posted by jonathancncs
0 comments posted 6yrs posted by jonathancncs

Reclaiming Harbor Freight milling Machine

Hi all, I picked up a Harbor Freight milling machine like this, > https://www.youtube.com/watch?time_continue=136&v=KBZ...
6 comments posted 6yrs
posted by nojunk
6 comments posted 6yrs posted by nojunk

Belt Grinders

Ok... I've talked about them before, but what is the advantage of a long belt grinder over a short one. I imagine heat...
3 comments posted 6yrs
posted by none
3 comments posted 6yrs posted by none

Flat Wrenches (2025 Update)

I'm sure most production flat wrenches are punched out of a piece of sheet, and deburred. I need to make a couple flat...
10 comments posted 6yrs
posted by none
10 comments posted 6yrs posted by none

'Lectrics Question

  I have a motor that calls for 2 177 Mfd start caps wired in parallel and I have in hand one 340-408 Mfd start cap . I...
2 comments posted 6yrs
posted by snag_one
2 comments posted 6yrs posted by snag_one

Motorhead question

So when I retire in a few years I want to build a sports car from scratch. I have the equipment and knowhow except for...
31 comments posted 6yrs
posted by etpm
31 comments posted 6yrs posted by etpm

Auction heads-up (Nashua, NH)

Last minute - closes tomorrow at noon. Inspection was last week, so pig-in-a-poke. https://www.bidspotter.com/en-us/auc...
2 comments posted 6yrs
posted by BobEngelhardt
2 comments posted 6yrs posted by BobEngelhardt

Insane Toolbox

No, its not one of those two story monstrosities with its own staircase. Its cheap. Even if it was the low quality of t...
3 comments posted 6yrs
posted by none
3 comments posted 6yrs posted by none

ISO20 Tool Holders

I recently converted one of the little 24K mills from a straight ER collet spindle to an ISO20 spindle nose. I LIKE IT...
0 comments posted 6yrs
posted by none
0 comments posted 6yrs posted by none

Deep Drilling, Straight, Long Reach, Aluminum

I need to drill some holes in 6061 aluminum. No problem. I have drilled a lot of holes in 6061 aluminum. The need to be...
27 comments posted 6yrs
posted by none
27 comments posted 6yrs posted by none

Yard sale score

  A dandy little red dot laser for my shotgun , five bucks and it was mine . The metalworking part is the bushing I had...
3 comments posted 6yrs
posted by snag_one
3 comments posted 6yrs posted by snag_one

Toyota 7fgcu25 hard start

Have a toyota 7fgcu25 with hard cold start. Forklift fires right up with a small shot of carb cleaner and runs perfect....
0 comments posted 6yrs
posted by 0f8503901d844703eea1acecb7a4938a_2557
0 comments posted 6yrs posted by 0f8503901d844703eea1acecb7a4938a_2557

Toyota 7fgcu25 hard start

Have a toyota 7fgcu25 with hard cold start. Forklift fires right up with a small shot of carb cleaner and runs perfect....
1 comments posted 6yrs
posted by Mr 915
1 comments posted 6yrs posted by Mr 915

ReWind the Transformer

Some years (10+) back I partially unwound the power transformer for my power supply on the Hurco mill so that I could s...
11 comments posted 6yrs
posted by none
11 comments posted 6yrs posted by none