⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

Speed / Feed / HP / Thrust chart - Titanium?

Looking for something conservative and similar to these: http://tinyurl.com/ToolSpeedsor http://www.multi-drill.com/dri...
0 comments posted 17yrs
posted by autodrill
0 comments posted 17yrs posted by autodrill

Hey Gunner!

Did you get the brass I sent you? Jim
2 comments posted 17yrs
posted by n427c
2 comments posted 17yrs posted by n427c

air separator in water line

The foot valve in the bottom of my well is starting to leak water again. Third time in 22 years. Its a 5 hp. unit 220 f...
7 comments posted 17yrs
posted by karltownsend.NOT
7 comments posted 17yrs posted by karltownsend.NOT

Power saw history

I had been told when visiting an old lumber camp tourist attraction that the circular saw was a mid-nineteenth century...
13 comments posted 17yrs
posted by stauffer
13 comments posted 17yrs posted by stauffer

Very Nice Metalworking

Sorry it's on topic, but I just hadda do it. I'm reading S.M. Stirling's _Peshawar Lancers_ and went online to find out...
1 comments posted 17yrs
posted by novalidaddress
1 comments posted 17yrs posted by novalidaddress

Sandblasting

Just a little follow up on the sandblasting cabinet. This is a "trinco 24" cabinet, 24x18 inside. I modified it very sl...
7 comments posted 17yrs
posted by ignoramus24511
7 comments posted 17yrs posted by ignoramus24511

Is this a head gasket (2000 Dakota)

=A0Well, I looked at the 2000 Dosge Dakota I have at home that was my brothers. 1st I tried to start it but it had sat...
15 comments posted 17yrs
posted by dgilbert
15 comments posted 17yrs posted by dgilbert

Wayne

Spent a while looking at pictures of your shop. What fun.
1 comments posted 17yrs
posted by ignoramus30547
1 comments posted 17yrs posted by ignoramus30547

making large diameter taps

I'm in the market for a specialty tap size, for threading bicycle bottom brackets, like this expensive tool: http://www...
22 comments posted 17yrs
posted by david.margrave
22 comments posted 17yrs posted by david.margrave

Axminster instructions

I have an Axminster drill grinding attachment that was in a box of stuff from my father's tools .Unfortunately , I don'...
21 comments posted 17yrs
posted by snagone
21 comments posted 17yrs posted by snagone

SKF bearing information

I'm trying to find SKF bearing information such as the fillet radius for the housing and shafts. To date I've been push...
17 comments posted 17yrs
posted by sfkf
17 comments posted 17yrs posted by sfkf

REQ: VFD recommendation

I would like a recommendation for a VFD that can drive a three-phase 5HP motor on an air compressor from a single-phase...
22 comments posted 17yrs
posted by devnull
22 comments posted 17yrs posted by devnull

gimbals?

I have a couple of laser levels, neither of which are self leveling. They do have bubble leveling. Is there any source...
6 comments posted 17yrs
posted by oldfart
6 comments posted 17yrs posted by oldfart

Model Steam Engine running

Hello, Thanks to all who had helped. Was able to get the old steam engine running: http://www.youtube.com/watch?v=x7pBxE...
6 comments posted 17yrs
posted by pauls77
6 comments posted 17yrs posted by pauls77

3 ton long stroke jacks $15

I got a couple of 3 ton long stroke jacks from a guy in Feasterville PA. ( North of Philly ). He has a bunch and can be...
0 comments posted 17yrs
posted by dcaster
0 comments posted 17yrs posted by dcaster